Bedienungsanleitung Scheppach KS55PS Kity (Seite 24 von 72) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

782280

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

24 GB

The edge of the splinter guard now corresponds

exactly to the cutting edge of the saw blade

Caution!

Always secure the workpiece in such a way that

it cannot shift.

Always move the machine forward; never pull it

toward the body.

TO SAW:

1. Set the saw on the guide rail.

2. Switch on the machine.

3. Press the saw slowly down to the set cut depth

and move this evenly forward along the rail.

PLUNGE CUTS:

To Saw:

1. Set the saw on the guide rail at the marked cut-

ting point

2. Secure the rebound protection or fence (acces-

sory not included) at the back and front cut points

on the guide rail.

3. Switch on the machine.

4. Press the saw down slowly to the set cut depth

and move this forward evenly on the rail up to the

front cutting point.

Tilt Protection

Put the rail saws with a the supplied anti-tilt. This pre-

vents the machine from tilting sideways when tilting.

This physical injuries or damage to the machine can

be avoided.

Use of the dust bag (Fig. 12)

Push the dust bag (21) onto the extraction nozzle

(12).

16. Accessories

This manual may contain descriptions of acces-

sories that are not included in the scope of sup-

ply of your machine!

Guide System

2 Pieces guide rails (A) á 700mm

1 Piece rail joiner (F)

1 Piece tilt protection

2 x professional screw clamps (B)

1 x dust bag (21)

1 x non-return mechanism (D)

Guide Device (Fig. 10, 11)

The guide rails (A) enable clean, precise cuts and pro-

tect the surfaces from damage.

When sawing with the guide rail, the cut depth is 4.5

mm less than the scale value on the machine.

For safety, the guide rail can be secured with screw

clamps (B) (not included).

The tilt protection prevents the plunge saw from tilting

during miter cuts and adjustment work.

The rebound protection (D) ensures a safe guiding

during plunging into the workpiece (not included).

By means of the rail joiner (F), 2 guide rails can be

connected and allow long, precise cuts

The guide clearance of the assembly on the guide rail

can be regulated with the two adjustment screws (E).

With the offered accessories, miter cuts, corner cuts

and other tting tasks can be carried out.

When rst using this saw on the optional guide rail,

it will need to be adjusted to slide with minimal side

movement on the guide rail, Adjustable cams (Fig 10

“E”) are tted to do this.

1. Place saw on guide rail.

2. Turn cams (Fig 10 “E”) anti-clockwise until tight.

Then clockwise slightly to allow clearance. While

holding dials in position lock in place by screwing

down the Socket head Cap screws in the middle

of each Cam (5mm allen key supplied with ma-

chine)

3. Pull saw back and forth along rail ensuring it

slides smoothly Re-adjust as needed.

4. Future adjustment may be needed depending on

use of saw.

Splinter Protection (guide rails)

The guide rail comes with a splinter guard, which

must be tted before the rst use.

1. Secure rail with the screw clamps to a piece of

scrap lumber.

2. Adjust the guide clearance on the rail with the two

adjustment screws (E).

3. Set the plunge saw to ca. 6mm cut depth

4. Set up the saw at the back end of the rail.

5. Switch on the machine, press down to the set cut

depth and t the splinter guard along the whole

length in one pass without stopping.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KS55PS Kity Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info