Bedienungsanleitung Scheppach KS55PS Kity (Seite 22 von 72) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

782280

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

22 GB

Only a qualied electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following

data:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

13. Maintenance

If specialist personnel must be brought in for extraor-

dinary service or repairs during the warranty period

and thereafter, please contact a service provider rec-

ommended by us or contact the manufacturer directly.

Overhauls, maintenance work, cleaning, as well as

the elimination of any malfunctions must only be un-

dertaken after turning off the motor.

All protective and safety equipment must be rein-

stalled immediately upon completion of any repair or

maintenance work.

Regular maintenance

The regular maintenance decribed above and in the

paragraph below can be carried out by unskilled per-

sonnel.

Do not oil the plunge cut saw, cause cutting must be

carried out in dry conditions; all rotating parts are self-

lubricating.

During maintenance, wear protective gear if possible

(accident-prevention goggles and gloves).

Remove cuttings when necessary both from the cut-

ting area, work surfaces and support bases.

Use of an aspirator or brush is recommended.

ATTENTION: Do not use compressed air jets!

Regularly check blade conditions: if difculties should

arise during cutting, have it sharpened by skilled per-

sonnel or replace it if necessary.

Assistence

When in need of skilled personnel for special main-

tenance, or for repairs, both during and following the

guarantee period, always apply to authorized centres

for assistance or directly to the manufacturer if there

is no authorized centre in your area.

Service information

Please note that the following parts of this product are

subject to normal or natural wear and that the following

parts are therefore also required for use as consumable.

Wear parts*: Carbon brushes, saw blade

* Not necessarily included in the scope of delivery!

Cutting with rails

1. Place the machine in the guide rails. can be read-

justed using the hex driver included in the deliv-

ery, when there is the risk of the adjusting screws

releasing by themselves.

2. Turn on the machine by pressing the on/off switch

(4).

3. Press the dip trigger (3).

4. Press the saw downwards to reach the sawing

depth. During rst use the rubber lip is sawn off

and thus splitter protection is guaranteed up to

the saw blade.

5. Push the saw uniformly forwards.

6. Turn off the machine and tilt the saw blade to the

top when the saw cutting is complete.

Sawing with dust suction

Connect the suction hose to the exhaust nozzle - Ø

38 mm (12).

12. Electrical connection

The installed electric motor is completely wired

ready for operation.

The customer’s connection to the power supply

system, and any extension cables that may be

used, must conform with local regulations.

Important remark:

The motor is automatically switched off in the event

of an overload. The motor can be switched on again

after a cool ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation

dam age. Possible causes are:

• Pinch points when connection cables are run

through window or door gaps.

• Kinks resulting from incorrect attachment or laying

of the connection cable.

• Cuts resulting from running over the connecting ca-

ble.

• Insulation damage resulting from forcefully pulling

out of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not

be used as the insulation damage makes them ex-

tremely hazardous.

Check electrical connection cables regularly for dam-

age. Make sure the cable is disconnected from the

mains when checking.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H05VV-F“.

The printing of the type designation on the connec-

tion cable is mandatory.

Single-phase motor

• The mains voltage must coincide with the voltage

specied on the motor’s rating plate.

• Extension cables up to a length of 25 m must have

a cross-section of 1.5 mm2.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KS55PS Kity Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info