Bedienungsanleitung Scheppach KSB56 - Woodster (Seite 43 von 76) (Deutsch, Englisch, Französisch)

782040

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

43GB

and spacer (A).

3. Mounting the stopper claw (Fig.3)

Insert the stopper claw (19) into the recesses of the

housing (see Fig. 3) and secure with the 2 xing

screws (19a). Use the tool supplied with the assem-

bly tools (10).

4. Slide the chain around the sprocket, next slide the

saw chain around the bar. Pay attention to the instal-

lation direction of the chain. (Fig.4-5)

5. Insert the chain tensioning screw (Z) into the lower

hole of the chain bar (Y). (Fig.4)

6. Install the cover (17) and tighten the nuts (B) by hand.

Installation direction of the chain (shown Fig.5)

Tensioning the chain (Fig.6-8)

1. Hold the front part tight with your hand.

2. Adjust the chain tension using the tension screw (C)

so that the chain rests entirely on the bar, but not un-

der great tension.

3. Tighten the mounting nut (B) for the bar with the key

(12-15 Nm).

4. Check with your hand that the chain runs smoothly

on the rail and has the proper voltage.

5. Where necessary, set up the chain tension.

IF THE CHAIN HAS TO BE RE-TENSIONED

Adjusting the chain tension

Correct saw chain tension is extremely important and

must be checked before starting operation and at regu-

lar intervals during all sawing work. If you take the time

to adjust the saw chain, you will improve your sawing

results and extend the chain’s service life.

m NOTE

If the chain is too loose or too tight on the drive wheel

and bar, the crankshaft bearings will wear out faster.

m NOTE

New chains expand, so they must be reset after about 5

cuts. This is normal for a new chain, and the future inter-

val settings will decrease.

Fuel and Chain Oil

m WARNING!: Fuel and chain oil are highly ammable.

Do not smoke and or expose the unit to an open ame

when you use the device.

Fuel

For optimal results, use normal unleaded fuel (max. 5%

Bio-ethanol) blended with special 2-stroke oil.

Fuel mixture

Mix the fuel with 2-stroke oil in a suitable container.

Shake the container to mix everything carefully.

m CAUTION!: Never use pure gasoline for this saw. It

will damage the engine and you will lose the warranty

for this product. Do not use a fuel mixture that has been

stored for longer than 90 days.

m CAUTION!: Special 2-stroke oil must be used for air-

cooled 2-stroke engines with a 40:1 ratio. Insu󰀩cient oil

will damage the engine and, in this case, void the war-

ranty for the motor.

FUEL MIXING TABLEE

Mixing ratio: 40 parts petrol to 1 part 2-stroke oil.

Petrol 2-stroke oil

1 Liter 25 ml

5 Liter 125 ml

After lling the fuel and chain oil tanks, close the tank

lid by hand.

Do not use tools to do so.

Recommended fuels

Some conventional gasolines are blended with ingredi-

ents such as alcohol or ether compounds to meet the

standards for clean exhaust gases. The engine runs sat-

isfactorily with all grades of gasoline, but for the purpose

of self-propulsion with oxygenated gasolines, it is best to

use regular gasoline. At best, use regular unleaded fuel

(max. 5% Bio-ethanol).

Oiling of the chain and bar

Every time the fuel tank is lled with gasoline, oil must al-

so be added to the chain oil tank.

It is recommended to use commercial chain oil.

1. Put the machine to the side (Housing cover saw

chain drive unit (17))

2. Remove the oil tank cap (14) and fuel tank cap (12).

3. Fill the chain oil tank (Fig.9/Pos.D1) to 80% with

chain oil.

4. Pour the petrol-/oil mixture into the fuel tank (Fig.9/

Pos.D2).

5. Close Oil tank cap (14) and fuel tank cap (12).

Chain Brake (Fig.14)

m NOTE

Before each use always check that the chain brake

is functioning.

• Hold the chain saw by the front handle (4).

• Press the front hand guard (3) forward to position (3b).

Press the pedal, the chain should not move.

• Pull the front handle (3) back to position (3a). Press

the pedal, the chain should move.

Oil Supply Control

To check the chain lubrication keep the chain on a piece

of paper and give full throttle for a few seconds. On the

paper the quantity of oil can be checked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KSB56 - Woodster Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info