Bedienungsanleitung Scheppach KSB56 - Woodster (Seite 45 von 76) (Deutsch, Englisch, Französisch)

782040

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

45GB

Other maintenance points before each use

• Check for leakage from oil or fuel tanks.

• Check the unit for loose parts and screws. Specically,

the chain, the bar and the hand grips.

• If you nd defects on the machine, x them immedi-

ately.

Oil-/Fuel lter (Fig.21)

m CAUTION!: Never operate the saw without the Oil-/

fuel lter (L1/L2). After every 100 hours of operation the

Oil-/fuel lter needs to be cleaned or replaced when

damaged. Drain the Oil-/fuel tank completely before re-

placing the Oil-/lter.

• Remove the Oil-/fuel tank cap (12/14).

• Make a handle from soft wire.

• Insert it into the opening of the Oil-/fuel tank and hook

the Oil-/fuel hose. Pull the Oil-/fuel hose carefully to

the opening until you can grab it with your ngers.

m NOTE

Pull the hose so it is not quite out of the tank.

• Lift the Oil-/fuel lter (L1/L2) from the tank.

• Remove the Oil-/fuel lter with a twisting motion and

clean it. If it is damaged, discard the Oil-/fuel lter.

• Insert the cleaned Oil-/fuel lter or a new one. Plug

one end of the Oil-/fuel lter into the tank opening.

• Make sure the Oil-/fuel lter is seated in the lower tank

cap. Move the Oil-/fuel lter with a long screwdriver to

put it in its proper slot.

• Fill the Oil-/fuel tank with fresh saw chain oil or fuel

mixture. Put the Oil-/fuel tank cap on the tank.

Spark plug (Fig.17-19,22)

m NOTE!: In order for the saw motor to remain pow-

erful, the spark plug (G) must be clean and properly

gapped (0.6-0.7 mm). Spark plugs should be cleaned or

replaced every 20 hours.

• Set the power switch (11) to „Stop“.

• Remove the air lter cover (5) by removing the air l-

ter mounting nut (6). The cover can then be removed.

• Disconnect the spark plug from the ignition wire by

gently pulling it and turning the spark plug (G).

• Remove the spark plug with a spark plug wrench (20).

Do not use other tools.

• Clean the spark plug with a copper wire brush or re-

place it with a new one. (Fig.22)

Adjusting the idling speed (Fig. 25)

If the saw chain continues to idle, you must correct the

idle speed.

1. Remove the plug (T).

2. Let the engine warm up for 3-5 minutes (no high

speeds!).

3. Turn the adjusting screw (R) using a at-head

screwdriver:

clockwise

- Idle speed increases (+)

counterclockwise

- Idle speed decreases (-)

Idling speed max.: 3500 min-1

Contact the manufacturer if the saw chain continues to idle.

Attention! Do not work on the chain saw!

Important: No adjustments can be made to the plug L / H.

Carburetor setting

The carburetor has been set to its perfect adjustment at

the factory. If it requires adjusting, take the saw to your

nearest authorized after-sales service outlet.

m WARNING!: You may not make settings on the car-

buretor itself!

Bar

• Check after every 8 hours of work to ensure uniform

wear.

Saw chain

Saw chain Tension

Periodically check the chain tension and adjust if nec-

essary, so that after use the chain is snug against the

rail, but still loose enough that it can be pulled by hand.

(Fig.8)

Breaking in a new saw chain

A new chain and bar will need chain readjustment after

as few as 5 cuts. This is normal during the breakin peri-

od, and the interval between future adjustments will be-

gin to lengthen quickly.

Chain lubrication

Always make sure the automatic oiler system is work-

ing properly. Keep the oil tank lled with Chain, Bar and

Sprocket Oil.

Adequate lubrication of the bar and chain during cutting

operations is essential to minimize friction with the guide

bar.

Never starve the bar and chain of lubricating oil. Run-

ning the saw dry or with too little oil will decrease cutting

e󰀩ciency, shorten saw chain life, cause rapid dulling of

chain, and lead to excessive wear of bar from overheat-

ing. Too little oil is evidenced by smoke or bar discolor-

ation.

MAINTAINING THE CHAIN

Sharpening the chain

Special tools are required to sharpen the chain; these

ensure that the cutting tools are sharpened at the cor-

rect angle and to the correct depth. We recommend

that inexperienced chainsaw users have the saw chain

sharpened by a specialist at the nearest customer ser-

vice location. If you are condent with sharpening your

own saw chain, procure the special tools from profes-

sional customer service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KSB56 - Woodster Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info