Bedienungsanleitung Scheppach KZS2000 Primaster (Seite 32 von 56) (Deutsch, Englisch, Französisch)

782511

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

32 | GB

8.7 Mitre cut 0°−45° and turntable 0°−45°

(g. 2/4/12)

The sliding compound mitre saw can be used to

make mitre cuts to the left of 0°−45° in relation to the

work face and, at the same time, 0°−45° to the left or

0°−45° to the right in relation to the stop rail (double

mitre cut).

Attention! For mitre cuts (inclined saw head), the left

side of the moveable stop rails (16a) must be xed in

the outer position.

• Open the set screw (16b) for the moveable stop rail

(16a) and push the moveable stop rail (16a) out-

wards.

• The moveable stop rail (16a) must be xed far

enough in front of the innermost position that the

distance between the stop rail (16a) and the saw

blade (6) amounts to a minimum of 8 mm.

• Before making a cut, check that the stop rail (16a)

and the saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Release the rotary table (14) by loosening the han-

dle (11).

• Set the rotary table (14) to the desired angle (refer

also to point 8.4 in this regard).

• Fold the locking handle (11) downwards to secure

the rotary table (14).

• Undo the set screw (22).

• Use the handle (1) to tilt the machine head (4) to the

left until it coincides with the required angle value

(in this connection see also section 8.6).

• Re-tighten the set screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (g. 3/13)

• The cutting depth can be innitely adjusted using

the screw (24). To do this loosen the knurled nut

(24a) on the screw (24). Turn the screw (24) in or

out to set the required cutting depth. Then re-tight-

en the knurled nut (24a) on the screw (24).

• Check the setting by completing a test cut.

8.9 Sawdust bag (g. 1/22)

The saw is equipped with a debris bag (17) for saw-

dust and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a

zipper at the bottom.

8.9.1 Connection to an external dust extractor

• Connect the vacuum hose with the dust extraction

spout.

• The industrial vacuum cleaner must be suitable for

the material being worked.

• When vacuuming dust that is especially detrimen-

tal to health or carcinogenic, use a special vacuum

cleaner.

8.10 Changing the saw blade (g. 1/2/14−17)

Remove the power plug!

Attention!

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing the machine head (4) upwards and lock with

the locking bolt (23).

• Loosen the retaining screw (5a) of the cover using

a Phillips screwdriver.

WARNING! Do not fully remove this screw.

• Fold the saw blade guard (5) upwards until the saw

blade guard (5) is above the ange screw (28).

• With one hand insert the Allen key (C) in the ange

screw (29).

• Hold the Allen key (C) and slowly close the saw

blade guard (5) until it touches the Allen key (C).

• Firmly press the saw shaft lock (30) and slowly ro-

tate the ange screw (28) in clockwise direction.

The saw shaft lock (30) engages after no more than

one rotation.

• Now, using a little more force, slacken the ange

screw (29) in the clockwise direction.

• Turn the ange screw (28) right out and remove the

outer ange (29).

• Take the blade (6) o󰀨 the inner ange (31) and pull

out downwards.

• Carefully clean the ange screw (28), outer ange

(29) and inner ange (31).

• Fit and fasten the new saw blade (6) in reverse or-

der.

• Attention! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (6)

must coincide with the direction of the arrow on the

housing.

• Before continuing your work make sure that all

safety devices are in good working condition.

• Attention! Every time that you change the saw

blade (6), check to see that it spins freely in the ta-

ble insert (10) in both perpendicular and 45° angle

settings.

• Attention! The work to change and align the saw

blade (6) must be carried out correctly.

8.11 Using the laser (g. 18)

Switching on:

Press the ON/OFF switch laser (33) 1x. A laser line

is projected onto the material you wish to process,

providing an exact guide for the

Switching o󰀨:

Press the ON/OFF switch laser (33) 1x.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KZS2000 Primaster Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info