Bedienungsanleitung Scheppach KZS2000 Primaster (Seite 33 von 56) (Deutsch, Englisch, Französisch)

782511

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

GB | 33

Brush inspection

Check the carbon brushes after the rst 50 operat-

ing hours with a new machine, or when new brushes

have been tted. After carrying out the rst check,

repeat the check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the

spring or contact wire are burned or damaged, it is

necessary to replace both brushes. If the brushes are

found to be usable following removal, it is possible to

reinstall them.

When servicing the carbon brushes, open the two

latches counterclockwise (as shown in gure 21).

Then remove the carbon brushes.

Replace the carbon brushes in the reverse order.

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: carbon brushes, saw blade, table in-

serts, sawdust bags

* Not necessarily included in the scope of delivery!

11. Storage

Store the device and its accessories in a dark, dry

and frost-proof place that is inaccessible to children.

The optimum storage temperature is between 5 and

30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

• The product meets the requirements of EN 61000-

3-11 and is subject to special connection condi-

tions. This means that use of the product at any

freely selectable connection point is not allowed.

• Given unfavourable conditions in the power supply

the product can cause the voltage to uctuate tem-

porarily.

• The product is intended solely for use at connec-

tion points that

a) do not exceed a maximum permitted sup-

ply impedance “Z” (Zmax = 0.382 Ω), or

b) have a continuous current-carrying capacity of

the mains of at least 100 A per phase.

8.12 Adjusting the laser (g. 19−20)

If the laser (32) ceases to indicate the correct cut-

ting line, you can readjust the laser. To do so, open

the screws (32b) and remove the front cover (32a).

Loosen the Phillips head screws (E) and set the laser

by moving sideways until the laser beam strikes the

teeth of the saw blade (6).

After adjusting and tightening the laser, mount the

front cover by tightening both screws (32b) by hand.

9. Transport

• Tighten the locking handle (11) to lock the rotary

table.

• Press the machine head (4) downwards and secure

with the locking bolt (23).

• Fix the saw’s drag function with the locking screw

for drag guide (20) in rear position.

• Carry the equipment by the xed saw table (15).

• When reassembling the equipment proceed as de-

scribed under chapter 8.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust o󰀨 the machine from time to time

using a cloth. In order to extend the service life of the

tool, oil the rotary parts once monthly. Do not oil the

motor.

When cleaning the plastic do not use corrosive prod-

ucts.

Cleaning the moving saw blade guard safety de-

vice (5)

Always check the saw blade guard for debris before

using the machine.

Remove old sawdust and splinters using a brush or

similar tool.

Replacing the table insert

Danger!

With a damaged table insert (10) there is a risk

of small parts getting stuck between table in-

sert and saw blade, blocking the saw blade.

Immediately replace damaged table inserts!

1. Remove screws at table insert. If required, turn ro-

tary table and incline saw head to be able to reach

the screws.

2. Remove table insert.

3. Install new table insert.

4. Tighten the screws at table insert.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach KZS2000 Primaster Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info