Bedienungsanleitung Scheppach Lata 5.0 (Seite 12 von 120) (Alle Sprachen)

782052

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

12 english

Manufacturer

Scheppach

Fabrikation von Holzbearbeitungsmaschinen GmbH

Günzburger Straße 69

D-89335 Ichenhausen

Dear customer,

We wish you much pleasure and success with your

new scheppach machine.

Note

In accordance with valid product liability laws, the

manufacturer of this device shall not be responsible

for damage to and from this device which results from:

• Improper care.

• Noncompliance with the Operating Instructions.

• Repairs made by unauthorized persons.

• The installation and use of any parts which are not

original scheppach replacement parts.

• Improper use and application.

• Failure the electrical system as a result of noncom-

pliance with the legal and applicable electrical direc-

tives and VDE regulations 0100, DIN 57113 / VDE

0113.

We recommend

that you read through the entire operating instructions

before putting into operation.

These operating instructions are to assist you in get-

ting to know your machine and utilize its proper ap-

plications.

The operating instructions contain important notes on

how you work with the machine safely, expertly, and

economically, and how you can avoid hazards, save

repair costs, reduce downtime and increase the reli-

ability and service life of the machine.

In addition to the safety requirements contained in

these operating instructions, you must be careful to

observe your country’s applicable regulations.

The operating instructions must always be near the

machine. Put them in a plastic folder to protect them

from dirt and humidity. They must be read by every

operator before beginning work and observed consci-

entiously. Only persons who have been trained in the

use of the machine and have been informed of the

various dangers may work with the machine. The re-

quired minimum age must be observed.

In addition to the safety requirements contained in

these operating instructions and your country’s appli-

cable regulations, you should observe the generally

recognized technical rules concerning the operation

of woodworking machines.

General notes

• After unpacking, check all parts for any transport

damage. Inform the supplier immediately of any

faults.

• Later complaints cannot be considered.

• Make sure the delivery is complete.

• Before putting into operation, familiarize yourself

with the machine by carefully reading these instruc-

tions.

• Use only original scheppach accessories, wearing

or replacement parts. You can nd replacement

parts at your scheppach dealer.

• When ordering, include our item number and the

type and year of construction of the machine.

Lata 5.0

Included with delivery

Wood turner lathe

Tool holder

Driver (Fig. 1.2, A)

Live tailstock center

Tensioning spindle (Fig. 1.2, C)

Face plate

Openend wrench SW 32 (gure 1.2, D)

Operating instructions

Technical data

Dimensions

L x B x H mm 1610 x 490 x 1175

Bed height mm 910

Headstock thread Art. Nr. 8800 1925 (1" x 8 TPI)

Art. Nr. 8800 1926 (M 33)

Spindle cone MK 2

Height of centers

above bed mm 175

Width between

centers mm 1050

Diameter above

bed mm 355

Diameter

between centers

282

Length of tool

holder mm 300

Face plate ø mm 150

Weight kg 85

Wood turning spindle with dust-proof precision grooved ball

bearing

Revolutions 1/min 500/600/750/900/1100/

1200/1400/1600/1800/2100

Tailstock

Tailstock cone MK 2

Tailstock drill hole

(hollow spindle)

ø mm

Tailstock sleeve

adjustment mm 55

Drive

Electric Motor 230–240V/50 Hz

Input P1 kW 0,75

Output P2 kW 0,50

Revolutions 1/min 1400

Motor protection yes

Undervoltage

release yes

Switch - plug

combination Netzstecker

Operating mode S6 40%

Noise parameters

The noise emission values at the work place, deter-

mined according to EN 23746 (acoustic power levels)

and EN 31202 (acoustic pressure levels) with a cor-

rection factor k3 calculated according to appendix A.2

of EN 31204, based on operating conditions listed in

ISO 7904, appendix A, are:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Lata 5.0 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info