Bedienungsanleitung Scheppach Lata 5.0 (Seite 14 von 120) (Alle Sprachen)

782052

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

14 english

• Any functional disorders, especially those affecting

the safety of the machine, sholud terefore be recti-

ed immediately.

• The scheppach wood turner has been constructed

exclusively for use with wood.

• Any other use exceeds authorization. The manufac-

turer is not responsible for any damages resulting

from unauthorized use; risk is the sole responsibility

of the operator.

• The safety, work and maintenance instructions of

the manufacturer as well as the technical data given

in the calibrations and dimensions must be adhered

to.

• Relevant accident prevention regulations and other,

generally recognized safety-technical rules must

also be adhered to.

• The machine may only be used, maintained, and

operated by persons familiar with it and instructed in

its operation and procedures. Arbitrary alterations

to the machine release the manufacturer from all re-

sponsibility for any resulting damages.

• The machine may only be used with original acces-

sories and tools made by the manufacturer.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial appli-

cations. Our warranty will be voided if the equipment

is used in commercial, trade or industrial businesses

or for equivalent purposes.

m Remaining hazards

The machine has been built using modern tech-

nology in accordance with recognized safety

rules. Some remaining hazards, however, may

still exist.

• Only process selected woods without defects such

as: Branch knots, edge cracks, surface cracks.

Wood with such defects is prone to splintering and

hazardous.

• Wood which is not correctly glued can explode

when being processed due to centrifugal force.

• Trim work piece to a rectangular shape, center and

correctly secure before processing. Unbalanced

work pieces can be hazardous.

• Injuries can occur when feeding work pieces if tool

supports are not correctly adjusted or if turning tools

are blunt. Sharp turning tools which are free of de-

fects are necessary for professional turning.

• Long hair and loose clothing can be hazardous

when the work piece is rotating. Wear personal pro-

tective gear such as a hair net and tight tting work

clothes.

• Saw dust and wood chips can be hazardous. Wear

pesonal protective gear such as safety goggles and

a dust mask.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following

the instructions in „Safety Precautions“, „Proper

Use“ and in the entire operating manual.

Assembly (Fig. 2 – 5)

Your drilling machine is subassembled for technical

reasons involved with packaging.

• Fig. 2 Slightly screw the frame feet in pairs with the

upper frame angle (each 3 neck bolts M8 x 12 with

washer and nut), put on sole plates.

• Fig. 3 Screw the bottom chassis with the frame feet

also only hand-tight (each 2 neck bolts M8 x 12 with

washer and nut).

• Place the frame on an even surface.

• Fig. 4 Place the drilling machine onto the frame and

rmly screw with the 8 Allen screws ;8 x 35, with

spring washer and nut.

• Finally tighten all the screws of the frame rmly.

• Fig. 5 Insert the switch from inside into the frame

foot and screw on with the Phillips head screw M4

with washer and nut.

Start-up

Observe the safety notes in the operating instruc-

tions before operating the machine.

Remove the tensioning spindle or the chuck from

the spindle in addition to any step-up tools before

rst operating the machine!

Reversing switch, Fig. 6

Your turning machine is equipped witha reversing

switch. The motor is always switched on and off using

the operating switch. I = green; 0 = red.

The reversing switch is merely a selector for the direc-

tion of rotation. You can change the direction of rota-

tion from anticlockwise to clockwise as you

require.

Note: The speed setting can only be done when en-

gine is running.

For safety reasons, it is not possible to switch directly

from anticlockwise to clockwise when the motor is

running. When the reversing switch is in 0-position it

switches the motor off, which must be switched back

on using the green switch.

Speed adjustment Fig. 7

The speed can only be adjusted during work.

The correct number of revolutions is visible on the

speed diagram located on the headstock. The speed

diagram is intended for medium-hard dry woods.

The appropriate speed is based on various factors

such as:

• type and compostion of woods

• seasoned, dry woods

• diameter and length of workpieces

• squared or unbalanced woods

• width of pre-worked, balanced workpieces

• wood turner tools and technique

• workpieces out of glued wood

Successful wood turning does not result from high

speeds, but rather, from correct use of the machine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Lata 5.0 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info