Bedienungsanleitung Scheppach MBS1100 (Seite 25 von 172) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Polnisch, Schwedisch)

781683

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 25

• Air intakes often cover moving parts and should

be kept clear. Loose-tting clothing, jewellery and

long hair may become caught in the moving parts.

6. Technical data

Motor 220 - 240 V ~, 50 Hz

Power 1100 W

Protection class II

Saw band 1140 x 12,7 x 0,65

Saw band speed 0,7 - 2,4 m/s

Cutting width 90° 127 x 127 mm

Cutting width 45° 127 x 40 mm

Swivel range 0°-45°

Weight Metal band saw 6,6 kg

Weight 13,6 kg

The total noise values determined in accordance

with EN 60745.

sound pressure level LpA 89 dB(A)

uncertainty KpA 3 dB

sound power level LWA 100 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The effects of noise can cause a loss of hearing.

Total vibration values (vector sum - three directions)

determined in accordance with EN 60745.

Vibration Ahv (front handle) = 6,62 m/s2

Vibration Ahv (rear handle) = 6,08 m/s2

Measurement uncertainty KPA = 1,5 m/s2

• The specied vibration emission value has been

measured according to a standardised testing pro-

cedure and can be used for comparison of one

electric tool with another;

• The specied vibration emission value can also be

used for an initial assessment of the load.

Warning:

• The vibration emission value can vary from the

specied value during the actual use of the elec-

tric tool, depending on the type and the manner in

which the electric tool is used;

• Try to minimise stress from vibrations as low as

possible. Some examples of means for reducing

the vibration stress are wearing gloves while us-

ing the tool and limiting work time. In doing so, all

parts of the operating cycle must be taken into ac-

count (such as times in which the electric tool is

switched off or times in which it is switched on, but

is not running under a load).

7. Remaining hazards

The machine has been built using modern technolo-

gy in accordance with recognized safety rules. Some

remaining hazards, however, may still exist.

• Risk of injury for ngers and hands by the rotating

saw band due to improper handling of the work

piece.

• Risk of injury through the hurling work piece due

to improper handling, such as working without the

push stick.

• Risk of damaging your health due to wood dust and

wood chips. Wear personal protective cloth such

as goggles. Use a tting dust extractor.

• Risk of injury due to defective saw band. Regu-

larely check saw band for such defects.

• Risk of injury for ngers and hands while changing

saw band. Wear proper gloves.

• Risk of injury due to starting saw band while

switching on the machine.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Wear only close tting clothes. Remove rings,

bracelets and other jewelry.

• For the safety of long hair, wear a cap or hair net.

Even when all safety measures are taken, some

remaining hazards which are not yet evident may

still be present.

• Remaining hazards can be minimized by follow-

ing the instructions in „General safety instructions“

„Proper Use“ and in the entire operating manual.

8. Operation

Before commissioning

• The saw band must be able to run freely.

• In case of previously machined wood, be aware of

any foreign bodies, such as nails or screws, etc.

• Before pressing the on/off switch, make sure that

the saw band is correctly tted, and that moving

parts run smoothly.

• Before connecting the machine, make certain that

the data on the type plate matches with the mains

power data.

Operating switch (g. 3)

CAUTION:

Before connecting the machine to the mains power

supply, make certain that the on/off switch is work-

ing correctly, and that it returns to the “OFF” position

when released.

• To switch on the machine, simply press the on/off

switch (5).

• To switch off, release the on/off switch (5).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MBS1100 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info