Bedienungsanleitung Scheppach MP132-40 (Seite 28 von 52) (Deutsch, Englisch, Französisch)

781693

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

28 | GB

Information concerning noise emission measured

according to relevant standards:

Sound pressure LpA = 79,7 dB(A)

Uncertainty KPA = 3 dB(A)

Sound power LWA = 90,9 dB(A)

Uncertainty KWA = 1,83 dB(A)

Wear ear-mu󰀨s.

The impact of noise can cause damage to hearing.

Vibration Ahv (left/right) = 8,125 m/s2

Uncertainty KPA = 1,5 m/s2

7. Before rst use

Before starting the equipment

Assembling the components

Some parts of the mower come disassembled.

For quick and easy assembly, read and follow the

instructions below.

Important! You will need the following additional tools

(not supplied) for assembly, and also for mainte-

nance work:

• A 1 liter measuring jug (oil/petrol resistant)

• A petrol can (5 liters is su󰀩cient for approx. 6

operating hours)

• A funnel (suitable for the tankʼs petrol ller neck)

• Household wipes (to wipe up oil/petrol residue;

dispose of these at a lling station)

• A petrol suction pump (plastic, available from DIY

stores)

• An oil can with hand pump (available from DIY

stores)

• Spark plug wrench

• 0,4 liter of engine oil (SAE 30/ 10W30)

Assembly

1. Take the mower and attachment parts out of the

packaging and check that all parts are present

2. Insert the bottom push bar (4a) in the hole in the

lawnmower and secure it with 2 screws (d).

3. Attach the upper push bar (4) on the lower push

bar (4a) with one screw (a), one washer (b) and

one star grip nut (5) each on both sides (Fig. 4-5).

4. Insert the pull start handle (17) in the designated

hook as shown in Fig. 6.

5. Fix the cables to the push bar with the cable clips

(18) provided (Fig. 7).

6. Grass box (16) - open it up and click the plastic

clips into position on the frame (Fig. 8).

7. Mowing with grass box:

Lift the discharge ap (15) with one hand and

hang the grass box (16) as shown in Fig. 9.

Setting the cutting height

m CAUTION!

Adjust the cutting height only when the engine is

switched o󰀨 and the plug boot has been pulled.

• Before you begin to mow, check to ensure that the

blade is not blunt and that none of the fasteners

are damaged.

• To prevent any imbalance, replace blunt and/or

damaged blades as a set only (if applicable). To

carry out this check, rst switch o󰀨 the engine and

pull the spark plug boot.

• locate the two front wheels as well as the two re-

ar wheels into the desired cutting height (30-48-

66 mm) position. (L = left-hand thread, R = right-

hand thread)

• ! ensure that the four wheels are xed in the sa-

me cutting height position (Fig. 13)

8. Operation

m CAUTION!

The engine does not come with oil in it. There-

fore, ensure that you add 0,4 liters of oil before

starting it up. Use normal, multigrade oil (SAE30).

The oil level in the engine must be checked each

time before mowing.

You will also need to ll in petrol, as this is also

not supplied upon delivery.

• In order to avoid any unintentional start-ups of the

lawn mower, it comes equipped with an engine

brake (Fig. 1/ Item 3) which must be pulled back

before the engine can be started. When the engine

control lever is released it must return to its initial

position, at which point the engine automatically

switches o󰀨.

• Press the engine brake lever (3) together and give

the starter cord (17) a vigorous pull. (Fig. 14)

Attention:

When you pull the starting rope the cutting blade

rotates even when dissolved motor brake lever.

Make sure that there are no body parts in danger

zone of cutting blade.

• Before you start mowing, you should run through

this operation several times in order to ensure that

the machine is working properly.

m WARNING

Whenever you need to perform any kind of ad-

justment and/or repair work on your lawn mower,

wait until the blade has come to a complete stop.

Always switch o󰀨 the engine before carrying out

any adjustments, maintenance or repairs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MP132-40 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info