Bedienungsanleitung Scheppach MS216A Kity (Seite 26 von 44) (Deutsch, Englisch, Französisch)

782498

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

26 GB

(7).

• Tighten the set screw (29) again. (2x 8.3 +8.4)

• Move the machine head (5) to its upper position.

• Use the handle (1) to push back the machine head

(5) and x it in this position if required (dependent

on the cutting width).

• Place the piece of wood to be cut at the stop rail

(18) and on the turntable (16).

• Lock the material with the clamping device (8) on

the xed saw table (16) to prevent the material from

moving during the cutting operation.

• Push down the release lever (3) to release the ma-

chine head (5).

• Press the ON/OFF switch (2) to start the motor.

• With the drag guide (23) xed in place:

use the handle (1) to move the machine head (5)

steadily and with light pressure downwards until the

saw blade (7) has completely cut through the work

piece.

• With the drag guide (23) not xed in place:

pull the machine head (5) all the way to the front.

Lower the handle (1) to the very bottom by apply-

ing steady and light downward pressure. Now push

the machine head (5) slowly and steadily to the

very back until the saw blade (7) has completely cut

through the work piece.

• When the cutting operation is completed, move the

machine head (5) back to its upper (home) position

and release the ON/OFF button (2).

Attention! The machine executes an upward stroke

automatically due to the return spring, i.e. do not re-

lease the handle (1) after completing the cut; instead

allow the machine head to move upwards slowly

whilst applying light counter pressure.

8.5 Cross cut 90° and turntable 0° - 45° (Fig. 1,6,7)

The crosscut saw can be used to make crosscuts of 0°

-45° to the left and 0° -45° to the right in relation to the

stop rail.

Attention! For bevel cuts (inclined saw head), the

moveable stop rail (28) must be xed in the outer posi-

tion.

• Open the set screw (29) on the moveable stop rail

(28) and push the moveable stop rail (28) outwards.

• The moveable stop rail (28) must be locked in a po-

sition far enough from the inner position that the dis-

tance between the stop rail (28) and the saw blade

(7) is no more than 5 mm.

• Before making the cut, check that no collision could

occur between the stop rail (28) and the saw blade

(7).

• Tighten the set screw (29) again. (2x 8.6 + 8.7)

• Use the handle (13) to adjust the rotary table (16)

to the desired angle. The pointer (14) on the rotary

table (16) must match the desired angle on the scale

(15) on the xed saw table (17).

• Tilt the locking lever (13) back up again to x the ro-

tary table (16) in place.

• Cut as described under section 8.3.

8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1,2,6,8)

The crosscut saw can be used to make mitre cuts of

0° - 45° in relation to the work face.

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (28) must be xed at the outer

position.

• Open the locking lever (29) for the adjustable stop

rail (28) and push the adjustable stop rail outwards.

• The adjustable stop rail (28) must be xed far

enough in front of the innermost position that the

distance between the stop rail (28) and the saw

blade (7) amounts to a maximum of 5 mm.

• Before making a cut, check that the stop rail (28)

and the saw blade (7) cannot collide.

• Secure the locking lever (29) again.

• Move the machine head (5) to the top position.

• Fix the rotary table (16) in the 0° position.

• Loosen the set screw (22) and use the handle (1)

to angle the machine head (5) to the left, until the

pointer (20) indicates the desired angle measure-

ment on the scale (19).

• Re-tighten the xing screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(Fig. 1,2,6,9)

The crosscut saw can be used to make mitre cuts to

the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the

right in relation to the stop rail (double mitre cut).

Important. To make miter cuts (inclined saw head),

the adjustable stop rail (28) must be xed at the outer

position.

• Open the locking lever (29) for the adjustable stop

rail (28) and push the adjustable stop rail outwards.

• The adjustable stop rail (28) must be xed far

enough in front of the innermost position that the

distance between the stop rail (28) and the saw

blade (7) amounts to a maximum of 5 mm.

• Before making a cut, check that the stop rail (28)

and the saw blade (7) cannot collide.

• Secure the locking lever (29) again.

• Move the machine head (5) to its upper position.

• Release the rotary table (16) by loosening the set

screw (26).

• Using the handle (13), set the rotary table (16) to the

desired angle (refer also to point 8.4 in this regard).

• Re-tighten the set screw (26) in order to secure the

rotary table.

• Undo the locking screw (22) and use the handle (1)

to tilt the machine head (5) to the left until it coin-

cides with the required angle value (in this connec-

tion see also section 8.6).

• Re-tighten the xing screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (Fig. 3)

• The cutting depth can be innitely adjusted using the

screw (26). To do this loosen the knurled nut on the

screw (26). Turn the screw (26) in or out to set the

required cutting depth. Then re-tighten the knurled

nut on the screw (26).

Scheppach MS216A Kity Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info