Bedienungsanleitung Scheppach MTP560 (Seite 24 von 156) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

781418

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

24 | GB

4. For operating the blades withdraw the accel-

erator trigger lock (5) and pull the clutch han-

dle (3) to start the rotation of the blades. Keep

the clutch handle (3) pushed downwards.

Release the clutch to stop the blades (Fig. 15+ 16).

9.1 Idle Speed (Fig. 14)

Set throttle control lever (16) to its “B” position to re-

duce stress on the engine when tilling is not being per-

formed. Lowering the engine speed to idle the engine

will help extend the life of the engine, as well as con-

serve fuel and reduce the noise level of the machine.

9.2 Shutting Down (Fig. 14 + 15)

Release tine clutch control lever (3) to neutral position

“C“ to stop the tines. To stop the engine switch the

throttle lever to position “C”

9.3 Operating Speed (Fig. 14)

For normal tilling:

• set the accelerator (16) to “ ” for best tiller action.

(Pos. A)

Cultivating.

• The accelerator (16) should be set to control a slow

walking speed “ “ for cultivating. (Pos. C)

10. Working instructions

10.1 Depth regulator

Besides depth regulator rod setting, variation of pres-

sure on the handles also helps further control of tilling

depth and travel speed. A downward pressure on the

handles will reduce the tilling depth and increase the

forward speed. An upward pressure on the handles

will increase the working depth and reduce the for-

ward speed.

10.2 Tiling

Tilling is digging in, turning over and breaking up gar-

den soil and preparing a seedbed for planting. Best

tilling depth is 100 mm to 150 mm. A tiller will also

clear the soil of unwanted vegetation. The decompo-

sition of this vegetation matter enriches the soil.

Avoid tilling soil that is too dry as it will pulverize and

produce a dust that will not hold water

- Water a few days before tilling.

Also, tilling soil that is too wet will produce unsatis-

factory clods.

- Wait a day or two after heavy rain for the soil to

dry.

Better growth will be obtained if an area is tilled prop-

erly and used soon after tilling to preserve the mois-

ture content.

8. Function

Throttle Lever (16)

It controls engine speed. Moving the throttle lever in

the directions shown makes the engine run faster or

slower. (Fig. 14)

Wheel (17)

The spring locks wheel bracket at di󰀨erent height and

distance from the tines. Pull the spring-connected wheel

bracket downwards to raise the wheel in the upper

groove when tilling. Set the wheel down when transport-

ing the tiller. Tilt the machine back until the tines clear the

ground. Push or pull the unit to the next location. (Fig. 13)

Depth Regulator Rod (10)

It regulates the tilling depth and helps the operator

control the direction and speed of the tiller.

Insert the depth regular rod in the groove at the rear of

the chassis, with the pointed end downward and the side

outward. Lowering the depth regulator rod will slow the

tiller and make it till deeper. Raising the depth regulator

rod will allow it to move faster and till shallower. (Fig. 5)

To adjust the tilling depth (Fig. 5):

1. Remove the pin. (Pos. B)

2. Raise or lower the depth regulator rod to the de-

sired position. (Pos. 10)

3. Replace the pin. (Pos. B)

9. Operation

Adding motoroil and gasoline

m ATTENTION! OIL HAS BEEN DRAINED FOR

SHIPPING.

Failure to ll engine sump with oil before starting en-

gine will result in permanent damage and void engine

warranty.

1. Check the oil level and top up if necessary oil.

(Max mark on the oil level indicator) (Fig. 11).

2. Open the fuel tank cap (2) and ll the device with

regular unleaded gasoline. (Fig. 12).

Starting the motor

1. Pivot the wheel (17) upwards until the locking en-

gages on the intended recess (Fig. 13).

2. Put the accelerator (16) into position (Fig. 14)

A= Full throttle

B= Idle

C= Stop

3. Set the throttle lever to the position “A”. Start the

motor using the recoil starter (1). To do this, rst

gently pull until you feel resistance, then pull hard

all the way. Repeat this operation until the motor

starts up. If the motor still does not start up after

ten attempts, refer to the “TROUBLESHOOTING”

section in this manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach MTP560 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info