Bedienungsanleitung Scheppach Multi Cut 5 (Seite 20 von 136) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

782264

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

parts of your body away from the sawing area

of the exposed saw blade. Any contact between

parts of your body and the rotating saw blade will

result in very serious injuries.

SAWING

Always use the saw as set out in these instruc-

tions.

Always support the workpiece near the cut (for

example using a saw stool or the like).

Always secure the workpiece so that the cut is on

your side.

Always secure the workpiece in a suitable device.

The workpiece must not be able to move whilst it

is being sawn.

Draw the line of the cut in pen on the workpiece

before you start the cut.

Position the front of the saw blades on the

actively supported part of the workpiece.

Never position the saw on the part of the work-

piece which will fall after the cut has been com-

pleted.

Always keep the cable away from the sawing area.

Route the cable so that it cannot become caught

up on the workpiece.

Maintain concentration at all times when using

the saw and keep it under control. This will make

the sawing work easier and above all safer.

If you lose your concentration whilst using the

saw and thus lose control of the saw, it may cause

accidents and serious injuries.

In the event that the cable becomes caught on

the workpiece whilst you are sawing, release the

ON/OFF switch immediately. Immediately pull the

plug out of the socket, check the cable for signs of

damage and then route it so that it can no longer

become caught on the workpiece.

In the event that the cable has been damaged,

the saw must be withdrawn from use straight

away. A damaged cable may result in serious

injuries or even death. Before you use the saw

again have the cable replaced by an authorised

workshop.

Push the ON/OFF switch forwards to switch on

the saw. Release the ON/OFF switch again to

switch off the saw.

After you have switched on the saw, wait until the

saw blades have reached their top speed before

you place them on the workpiece.

If the saw blades are brought into contact with

the workpiece before they have reached their top

speed, this can result in recoil and serious injuries.

Guide the saw calmly and with uniform pressure

through the workpiece as you are using it. If you

exert excessive pressure it will result in irregular

cutting results and will also reduce the service

life of the saw blades and saw. It may also cause

recoil.

When you are sawing through a workpiece, the

pivot safety hood does not cover the saw blade

POUIFVOEFSTJEFPGUIFXPSLQJFDF:PVTIPVME

therefore keep your hands, fingers and all other

parts of your body away from the sawing area

of the exposed saw blade. Any contact between

parts of your body and the rotating saw blade will

result in very serious injuries.

When you have sawn through the workpiece and

you then raise the saw off the workpiece, the saw

blades will be exposed until the pivot safety hood

closes. Ensure that the safety hood is completely

closed before you put down the saw.

When cutting metals such as aluminium, copper,

stainless steel or cast iron, always use the integral

lubrication device since these material tend to

adhere to the saw blades.

When sawing these materials, pay very close

attention to ensuring that the direction of the saw

is always parallel to the saw blade since otherwise

the saw blade will become so hot that it could

burn or the damage the saw teeth.

INSTRUCTIONS FOR CROSS CUTTING

B10 Flat bar iron

Position the saw blade perpendicular to the

cutting surface.

B11 Corner pieces

Guide the saw blade at a diagonal through

the cutting surface.

B12 Rectangular tubing

Guide the saw blade from corner to corner.

B13 U-shaped sections

Guide the saw blade from corner to corner.

B14 Aluminium, copper, stainless steel, cast iron

The lubrication device must always be used

for cutting these materials.

B15 Shaped platE

Plate must always rest on three supports one

of which must be next to the cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Multi Cut 5 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info