Bedienungsanleitung Scheppach Multi Cut 5 (Seite 18 von 136) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

782264

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

support parts with carbide metal teeth.

Never slow down or stop the saw blades by exer-

ting lateral pressure on them.

Never use carbide metal-tipped saw blades with a

residual height or thickness of less than 1 mm.

WARNING

Never use saw blade types other than those spe-

cified for use. This counterrotating twin blade saw

is fitted with special saw blades. The use of other

saw blades is not safe and may result in serious

accidents.

Always ensure that the saw has reached its full

speed before bringing it into contact with the

material. If the saw is brought into contact with

the material before it has reached its top speed, it

may cause very serious injuries.

Always ensure that both saw blades engage

simultaneously into the workpiece. If the saw

engages in a workpiece on one side, there is a

risk that the saw will suffer unexpected recoil and

cause serious injury.

For angled cuts, do not position the saw at an

angle so that only one blade engages in the work-

piece, but instead position it on the top so that

both blades engage at the same time.

The side areas of the saw blades are not designed

for cutting. When making cross cuts, therefore,

ensure that the weight of the saw is not suppor-

ted on the lower saw blade.

Instead support the saw by raising it slightly and

securing the workpiece in a clamp or vice. This

will prevent unexpected recoil.

When the machine is working it will generate dust

which may be harmful, inflammable or explosive.

Take suitable safety precautions. Wear a dust pro-

tection mask. Ensure that there is good ventilati-

on at the workplace.

RECOIL – CAUSES AND PREVENTION

Incorrect use and/or incorrect working methods

or conditions may cause the saw to recoil. The fol-

lowing action can be taken to prevent recoil.

Always hold the saw with two hands. Adopt a

posture in which your body and your arms can

withstand the recoil force.

In the event that the saw blade becomes stuck

in the workpiece or a cut is interrupted for any

reason whatsoever, release the ON/OFF switch

immediately and leave the saw in the workpi-

ece until the saw blade has reached a complete

standstill. Never take the saw out of a workpiece

whilst it is still running. This may cause the saw

to recoil. Identify and rectify the cause of the saw

becoming stuck.

When you reposition the saw on the material, the

saw blade must be placed in the centre of the cut.

Ensure that the saw’s teeth do not engage in the

material to the side of the cut. This may cause the

saw to recoil.

When sawing large panels please note that they

will bend slightly under their own weight and

this may cause the saw blade on the saw to block

which can thus result in recoil. Support these

panels using suitable equipment on both sides of

the panel. Place the supports near the line along

which you want to cut and close to the edge of

the panel.

Never use damaged or blunt saw blades. As the

saw blade wears, the kerfs created by this saw

blade will become too narrow which will cause

excessive friction resulting in the saw blade jam-

ming and possibly recoil.

If you wish to cut into existing walls or other

concealed areas, proceed with special care and

caution. Since you cannot know what is behind

the area you are cutting, you must expect recoil

to occur at any time.

ADDITIONAL INSTRUCTIONS FOR HANDLING

COUNTERROTATING TWIN BLADE SAWS

:PVNVTUIBWFSFBEBOEVOEFSTUPPEBMMUIF

instructions in this document and you must also

follow them. Also make sure that any other users

receive a copy of this document and your own

instructions and that they have read and under-

stood them. Any failure to follow the instructions

may result in electric shocks, fire and very serious

injuries.

Check the cable and the ON/OFF switch on the

tool at regular intervals. Have the cable and/or

switch repaired immediately in a special work-

shop if it / they are damaged. Following this

instruction will reduce the risk of serious injuries,

electric shocks and fires.

Check the saw at regular intervals for signs of

damaged parts and to ensure that it is in perfect

working order. Do not use the saw if it is dama-

ged or malfunctions. Damage and malfunctions

must be repaired / rectified immediately. Check

at regular intervals whether moving parts are

correctly aligned and are not seized. Also check

that no parts are broken and that there are no

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Multi Cut 5 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info