781480
13
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
english 13
Do not overload the machine by too much pressure against
the grinding roll.
After finishing the grinding turn off the machine and dis-
connect the main plug.
ATTENTION!! Use dust mask, protective goggles and vacuum
extraction.
m Electrical connection
The installed electric motor is factory connected ready for
operation. The connection meets the applicable VDE and
DlN regulations.
The connection made by the customer as well as any ex-
tension cables used must comply with all relevant regula-
tions.
Connection and repair work on the elctric equipment must
be carried out by a qualified technician only.
Important note
The motor rating is S 1. This means that when overloaded
it switches off automatically. After a cooling period (can
vary) you may switch it on again.
m Maintenance
Disconnect the main plug before conducting any maintenance
work.
Cleaning the machine after every use is recommended.
Keep the safety devices, air boxes and the crankcase
clean.
Clean the machine with a cloth.
Do not use any solvents or cleaning agents because they
could harm the plastic parts of the device.
Do not let water get into the interior of the machine.
The interior of the machine is completely maintenance-
free.
Trouble shooting
Problem Possible Cause Help
Motor doesn’t start
a) ON/OFF switch damaged.
b) ON/OFF cable damaged.
c) ON/OFF relay damaged.
d) Fuse blown.
e) Motor burnt.
a-d) Replace all damaged parts before you use
your machine again.
e) Contact your local service centre. Every
attempt to carry out a repair, can be
dangerous if it is not done by skilled
personnel.
Machine gets slower
during work. Too much pressure put on the workpiece. Reduce the pressure on the workpiece.
Sanding belt comes off
the drive pulleys. Belt does not run straight. Reset the track.
The wood gets burnt
during sanding.
a) Sanding disc or belt covered with grease.
b) Excessive pressure on workpiece.
a) Replace disc or belt.
b) Reduce pressure on workpiece.
Strong vibrations a) loosely mounted tool
b) defective tool
c) spindle knocks
a) tighten tool
b) change tool
c) repair at a Service-Station
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Scheppach OSM100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info