Bedienungsanleitung Scheppach OSM600 (Seite 21 von 116) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

781479

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 21

• Never leave the working area of the sanding ma-

chine while the tool is running, or as long as it has

not come to an absolute standstill.

• Always place the work piece on the grinding table.

To sharpen bent tools with the grinding disc, place

them securely on the table.

Remaining hazards

The machine has been built using modern technology

and in accordance with recognized safety rules.

Some hazards, however, may still remain.

• The grinding wheel poses a danger of injury to n-

gers and hands by improper feeding or placement

of tools.

• Danger of injury from thrown tools due to improper

holding or feeding.

• The use of incorrect or damaged mains cables can

lead to electrical injuries.

• Although having regarded all considerable rules

there may still remain not obvious remaining hazrds.

• Minimize remaining hazards by following the in-

structions in ”Safety Rules”, ”Use only as author-

ized” and in the entire operating manual.

6. Technical data

Dimensions L x W x H (mm) 465/420/500

Speed (1/min) 2000

Oscillation stroke (mm) 16

Belt dimensions (mm) 610x100

Belt Speed (m/s) 8

grinding height max. (mm) 90

Table Size (mm) 410x425

Table Tilt 0°-45°

Vacuum connector ø (mm) 38

Weight (kg) 12,9

Drive

Motor (V~/Hz) 220-240/50

Power (W) 450

Subject to technical changes!

Total vibration values determined in accordance with

EN61029

sound pressure level LpA 76 dB(A)

uncertainty KpA 3 dB

sound power level LWA 89 dB(A)

uncertainty KWA 3 dB

Wear hearing protection.

The e󰀨ects of noise can cause a loss of hearing. Total

vibration values (vector sum - three directions) deter-

mined in accordance with EN 61029.

7. Attachment and operation

Before starting the equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

m WARNING!

Always pull the power plug before making

adjustments to the equipment.

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the grinding/sanding belt

and disk to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you actuate the On/O󰀨 switch, make sure

that the abrasive paper is correctly tted and that

the equipment‘s moving parts run smoothly.

Connection to vacuum suction.

The use of an extraction system is recommended.

7.1. Tool changes, Fig. 2 - 7

m ATTENTION! Turn o󰀨 the machine and disconnect

the main plug.

When changing tools make sure to have all parts

cleaned.

• Prepare the appropriate tool and mount it as fol-

lows:

• Insert cover (6) in table (2)

• Insert stage plate (8) into the cover (6) (Fig. 4)

• Attach the lower spindle disc (7) to the spindle (1)

(g.5).

• Slide the abrasive sleeve (9) onto the rubber sleeve

(7) (g. 5).

• Apply the disc (D) (use the correct measurements)

(g. 7).

• Put on the hex-nut and tighten it with the hook

wrench (F). (g. 8)

Be sure always to mount the correct parts when

changing the abrasive sleeves. The table inlays have

to be bigger than the abrasive sleeves.

Note! The 13 mm abrasive sleeve is put directly onto

the spindle (1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach OSM600 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info