Bedienungsanleitung Scheppach OSM600 (Seite 22 von 116) (Deutsch, Englisch, Französisch, Italienisch, Polnisch)

781479

Zoom out

Zoom in

Vorherige Seite

1/116

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

22 | GB

Table:

Abrasive sleeve

inside D

Table inlay

inside D

Spindle disc

size

13 mm 13 mm small 16 mm

19 mm 19 mm medium 22 mm

26 mm 26 mm medium 22 mm

38 mm 38 mm large 44 mm

51 mm 51 mm large 44 mm

7.2 Installing the abrasive belt (Fig. 9,10)

m ATTENTION! Switch o󰀨 the machine and pull

out the mains plug.

• Remove the abrasive sleeve (9), rubber sleeve (7),

stage plate (8) and cover (6) if already mounted.

• Guide the grinding belt attachment (10) over the

spindle (1) and the stud (G) into the groove provided

for this purpose.

• Also make sure that the recesses (H) on the attach-

ment are inserted into the notches. If the recesses

do not engage immediately, turn the abrasive belt

by hand until they engage.

• Screw washer (B) and locking screw (A) onto the

spindle (1).

7.3. Changing the grinding/sanding belt (11)

(Fig. 11)

• Pull out the power plug.

• Turn the grinding/sanding tensioner (13) to the right

in order to reduce the tension on the grinding/sand-

ing belt (11).

• Remove the grinding/sanding belt (10).

• Mount and the new grinding/sanding belt in reverse

order. Important. Note the running direction: On

the housing and on the inside of the grinding/ sand-

ing belt!

7.4. Adjusting the grinding/sanding belt (11)

• Pull out the power plug

• Push the grinding/sanding belt (11) by hand slowly

in the running direction.

• The grinding/sanding belt (11) must run centrally on

the grinding/sanding surface. If not, you can use

the knurled screw (14) to make adjustments.

7.5 Fasten stop (12) (Fig. 12)

• Insert the workpiece stop (12) with the recess in

the groove on the table and fasten with the xing

screw (C).

Mounting sander to work bench

If your belt/disc sander is to be used in a permanent

location, it is recommended you secure it to a work-

bench or other stable surface.

• Mark holes on workbench where belt/disc sander

is to be mounted using holes in the base as a tem-

plate for hole pattern.

• Drill holes through workbench.

• Place belt/disc sander on workbench aligning holes

in the base with holes drilled in the workbench.

• Insert bolts (not included) and tighten securely with

lock washers and hex nuts (not included). Note: All

bolts should be inserted from the top. Install the

lock washers and hex nuts from the underside of

the workbench.

Clamping sander to work bench

If your sander is to be used as a portable tool, it is

recommended you fasten it permanently to a mount-

ing board that can easily be clamped to a workbench

or other stable surface.

The mounting board should be of su󰀩cient size to

avoid tipping while belt/disc sander is in use. Any

good grade plywood or chipboard with a 3/4 in.

(19 mm) thickness is recommended.

• Mark holes on board where belt/disc sander is to

be mounted using holes in the base as a template

for hole pattern.

• Follow last three steps in section Mounting Belt/

Disc Sander to Workbench.

If lag bolts are used, make sure they are long enough

to go through holes in belt/disc sander base and mate-

rial the belt/ disc sander is being mounted to. If ma-

chine bolts are used, make sure bolts are long enough

to go through holes in belt/disc sander, the material

being mounted to, and the lock washers and hex nuts.

7.6 On/O󰀨 switch (3)

• The grinder/sander can be switched on by pressing

the green button „1“.

• To switch o󰀨 the grinder/sander you must press the

red button „0“.

m WARNING: Do not reach across the sanding disc

to turn the belt/disc sander ON or OFF. Contact with

the sanding disc can result in serious personal injury.

7.7 sanding

• Always hold the workpiece rmly during grinding/

sanding.

• Do not exert excessive pressure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach OSM600 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info