Bedienungsanleitung Scheppach OX7-1600 (Seite 21 von 38) (Deutsch, Englisch, Französisch)

781945

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

16 english

• For speciﬁ c instructions regarding the drive shaft, refer

to its user manual (delivered with the drive shaft).

• For maintenance work or if the splitting wedge is stuck,

disconnect the machine from the tractor ﬁ rst, after stop-

ping the tractor.

Never leave the machine unattended while it is still con-

nected to the power source!

m Electrical Connection

Inspect the power cords regularly for damage. Make sure

that during this inspection the power cord is not connected

to the mains supply.

The power cords must comply with the applicable VDE

(German Association for Electrical, Electronic, and In-

formation Technologies) and DIN (German Institute for

Standardization) regulations. Use only power cords with

the designation H 07 RN.

A type label on the power cord is prescribed.

Faulty power cords

Power cords often suffer insulation damages.

Causes are:

• Pinching, when power cords are routed through windows

or door cracks.

• Bending due to improper attachment or routing of the

power cords.

• Cuts due to driving over the power cords.

• Insulation damages caused by yanking it out of the pow-

er outlet.

• Cracks in the insulation because of ageing.

Such faulty power cords must not be used and are, due to

the damaged insulation,

danger to life

Three-phase motor 400 V/ 50 Hz

Power supply 400 volts / 50 Hz.

Power cord and extension cord must have 5 conductors

= 3 P + N + PR. - (3/N/PE).

The extension wires must have a cross-section of at least

2.5 mm² and must not be longer than 20 m.

The power supply must be protected by a 16 A (or less)

circuit breaker.

After connecting the power supply or after relocating, check

the direction of rotation. Invert polarity if necessary.

Turn the polarity inverter inside the power plug.

Maintenance

Retooling, adjustment and cleaning activities are only to

be carried out when the motor is switched off.

Unplug the mains plug.

Experienced craftsmen may perform minor repairs them-

selves.

Repair and maintenance activities on the electric equipment

may only be carried out by an electronics specialist.

All protection and safety appliances must be ﬁ tted imme-

diately after completion of repair and maintenance work.

We recommend:

•Clean the machine thoroughly after each use!

•

Splitting knife

The splitting knife is a consumable which

might need regrinding/re-sharpening or which has to be

replaced with a new one.

•

Two-hand operating facility

The control and operating facility must remain smooth-

running. Lubricate occasionally with a few drops of oil.

•

Movable parts

Keep the splitting knife guides clean. (dirt, splinters,

bark, etc.)

Lubricate slide bars with spray oil or grease

•

Check oil level of hydraulics

Check hydraulic connections and screws for tightness and

abrasive wear. If necessary retighten the screw connec-

tions.

When do I change the oil?

First oil change after 50 operating hours, then always after

250 operating hours.

Check the oil level.

Check the oil level frequently before each start-up. If the

oil level is too low, the oil pump may be damaged.

Note:

The oil level must be checked while the splitting kni-

fe is retracted. The oil dipstick is located on the splitting

column in the ﬁ ller plug A (Fig. 5) und is provided with 1

slot. If the oil level is at the lower end of the dipstick, this

indicates that the minimum oil level has been reached. If

this is the case, the oil must be reﬁ lled immediately. The

slot indicates the maximum oil level.

The oil tank is situated in the splitting column and is ﬁ lled

with high-quality hydraulic oil by the manufacturer.

Change of the hydraulic oil and the oil ﬁ lter.

Place a container under the suction hose. Remove the hose

clamp of the pump and pull off the suction hose. Caution:

allow the oil to ﬂ ow into the container! Fig. 7

Remove the suction hose completely and by slightly tilting,

allow the remaining oil to drain into the container.

To change or clean the ﬁ lter, remove the entire intake ma-

nifold by means of a ﬂ at spanner SW41 or pipe wrench!

Fig. 7.1

Clean the ﬁ lter and re-mount with new sealing tape, item

no.: 1607 0333. Connect the suction hose again and se-

cure with hose clamps.

Remove the ﬁ ller plug and ﬁ ll with new hydraulic oil.

Attention! Make sure that no dirt particles enter the oil tank.

Dispose of used oil accordingly by taking it to the local waste

oil collection points. It is prohibited to drain used oil into the

soil or to mix it with waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach OX7-1600 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info