Bedienungsanleitung Scheppach OX7-1600 (Seite 20 von 38) (Deutsch, Englisch, Französisch)

781945

Zoom out

Zoom in

Vorherige Seite

1/38

Nächste Seite

english 15

with the nuts in order to lock the cylinder (Fig. 4).

• The nuts and the washers are located on the control le-

vers (Fig. 4.1)

• Never move upwards quickly, do not apply force!

• Errors in handling and operation are hereby explicitly

excluded from the warranty.

• Now release the operating knobs, the splitting wedge is

pulled upwards by the plunger. The wood splitter is now

ready for use.

Only use cardan shafts with CE signs, declaration of confor-

mity and operating instructions! Read these operating in-

structions carefully prior to operation!

Perform the above procedures only when the motor and the

PTO connector are turned off and the ignition key is remo-

ved!

Adjustment during the lowering of the cylinder

• Adjust the nut to the lower hole on the bar. Lower the

splitting knife onto a piece of wood of about 15 cm

height, switch off the machine. Fig. 6

• Unfasten the screw nuts on the cylinder, press an opera-

tion knob, and turn on the machine.

• Release the operation knob slowly. Lower the cylinder

slowly, and switch off the machine.

Splitting

• At temperatures below 5°C leave the machine at idle

speed for about ﬁ ve minutes so that the hydraulic sys-

tem reaches operating temperature.

• Place the wood under the splitting knife in an upright

position und press against the ﬁ xing bolt.

• Warning. The ﬁ xing bolt and the splitting knife are very

sharp. Risk of injury!

• When you press down both operating levers simulta-

neously, the splitting knife moves down and splits the

wood.

• Only split timber that has been cut straight.

• Split the wood vertically.

• Never split wood horizontally or diagonally!

• Wear appropriate gloves while splitting wood.

Length of wood

The hydraulic splitter is suitable for the splitting of short

wood and wood by the metre. It is practical to adjust the

upper stroke limitation to 3 to 5 cm.

Short wood max. 65 cm: Use the splitting table (optional

accessory) for the splitting.

Lifting limitation

• If you have logs of wood with a length of more than 100

cm place the nut in the upper hole of the bar

(Fig. 3) and clamp with the locking pin.

• If you have logs of wood with a length of less than 65

cm place the nut in the middle hole and clamp with the

locking pin.

Start-Up

Make sure that the machine is completely and properly

assembled. Before every use, check:

• the power cords for faults (cracks, cuts and such),

• the machine for possible damages,

• if all bolts are fastened tightly,

• the hydraulic system for leaks, and

• the oil level.

Power on/off

Press the green button to power on.

Press the red button to power off.

Note:

Check the function of the on/off-unit before every

use by switching it on and off once.

Restart cut-out in case of power failures (zero voltage

switch)

In case of a power failure, unintentionally pulling the pow-

er plug or a defect fuse the machine will automatically

switch off. To restart the machine, press the green button

on the switchbox again.

Operation with PTO

• Before connecting the machine to the three-point hitch

of the tractor, make sure that the weight of machine is

within the tractor’s speciﬁ cations. The weight of the ma-

chine can be found on the manufacturer type plate (ﬁ g.

1).

• Make sure that the machine is connected correctly to

the three-point hitch and that the safety bolts are always

in place.

• When working, be careful in order to prevent accidents

or damages.

• Only connect the drive shaft only to the engine of the

tractor when it is not running.

• Use only drive shafts that are approved and suitable for

the use with the log splitter. Furthermore the drive shaft

must be equipped with all safety mechanisms, which

must be in good condition.

• Keep away from the drive shaft when it is in use.

• Make sure that the shaft speed of the tractor does not

exceed the value speciﬁ ed on the type plate (max 300

rpm).

• It is recommended to wear earplugs or equivalent hear-

ing protection.

• Do not operate the machine indoors. The exhaust fumes

are harmful to health. They can cause unconsciousness

and therefore pose a threat to the operator. If it is neces-

sary to work indoors or in covered surroundings, make

sure that there is sufﬁ cient ventilation. Do not inhale the

exhaust fumes!

Modiﬁ cations of any kind to the machine are prohibited!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach OX7-1600 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info