Bedienungsanleitung Scheppach Plana 3.0 (Seite 15 von 128) (Alle Sprachen)

782085

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

14 english

ty warnings and using the machine in compliance with

the regulations, as well as following the operating in-

structions.

m Electrical Connection

• Check power line. Do not use any defective lines. See

Electrical Connection.

• Observe the motor and the tool rotation direction. See

Electrical Connection Planing Machine

• Installations, repairs and servicing of the electric in-

stallation must only be done by an expert professional.

• Disconnect the machine to avoid breakdowns. Discon-

nect the power plug.

• Turn off the motor when leaving the machine. Discon-

nect the power plug.

• Disconnect from all power sources even for an insigniﬁ-

cant relocation of the machine! Before starting the ma-

chine again, connect it properly to the power source!

Connect the machine to the power source with a CEE-

plug, use 16 A to secure the cable. Press the green button

on the operating switch, the planer shaft is running (Fig.

2).

Press the red button to turn off, the planer shaft will slow

down within 10 seconds. Changes in rotation direction

The rotation direction must be checked when connecting

to the power or after moving the machine, if necessary the

polarity must be changed using a screwdriver (machine

socket, Fig. 3).

The installed electrical motor is connected and ready

for use. The connection meet the corresponding VDEand

DIN-regulations. The power connection on the part of the

client, as well as the extension cables used, must meet

EVU-(Electricity Board) regulations.

OPERATION MODE/ POWER-ON TIME

The electrical motor is sized for S 6/40 % use. S6 = con-

tinuous operation with load burden 40% = based on 10

min. 4min. loading; 6min. open-circuit operation The mo-

tor shuts down on its own when overloaded, while a wind-

ing thermostat is embedded in the motor. After cooling

(time can vary) the motor can be switched on again.

DEFECTIVE ELECTRICAL POWER LINES

• Often there are isolation defects in electrical power

lines. Possible causes:

• Dents, when the power line was installed through a

window or doorway.

• Cracks resulting from an improper mound or installa-

tion of the power line.

• Cuts from passing around the power line.

• Isolation defects due to pulling out the wall socket.

• Rifts because of changes in isolation. Such defective

electrical power lines must not be used and are, due

to isolation defects life-threatening!

Check the electrical power line regularly for defects. Make

sure that the power line is not connected to the power

supply system during checkup. The power lines must meet

the VDEand DIN-regulations, as well as the local EVEregu-

lations. Use only the power lines with the mark H 07 RN.

An identiﬁcation on the cable of the type of line is manda-

tory.

Extension cables must be up to 25 m per each 1,5

squared millimeter section, over 25 m long for a section

of at least 2,5 squared millimeters. The power connection

must be supported by a 16 A fuse.

ROTARY MOTOR

Line voltage must be 380÷420 V 50 Hz. Power connec-

tion and extension cabling must be up to 5 cores (5adrig)

=3 P + N + SL.

Extension cables must cover a section of at least 1,5 m2.

The power connection should optimally be secured by 16

The rotation direction must be checked after connection

to the power or moving the machine, if necessary, the po-

larity must be changed.

• Connection and repairs of the electrical equipment

should only be done by an electrician. For inquiries,

please have the following information:

• Motor manufacturer; motor type

• Electrical type of the motor

• The machine/type plate information

• Electrical control system information

When sending back the machine, please include the com-

plete propulsion unit with the electrical control system.

m Maintenance

Conduct maintenance, repair and cleaning, as well as

malfunction check, only with the unit shut off. Use the

on-off switch to shut down the machine and then discon-

nect from the oulet!

All guard and safety instructions must be immediately

mounted after repair and servicing work. The work table,

as well as the thicknessing table must be kept free of res-

in. You can get Pharmol-HEK resin remover concentrate

type Nr. 6100 9700 from your specialist dealer.

Use long-term lubrication for the storage of the planer

shaft and the tool spindle. In new conditions, warming is

part of the design but it goes away after some time. Clean

the feeder cylinders regularly. Oil the bearing and shaft

with hinges of the sliding bearing of the feeder cylinders

and the adjustment spindle of the thicknessing table after

the ﬁrst 5 hours of operation. After that, oil every 20 hours

of operation.

Check the chain tension. If needed, tighten and oil it.

When tightening the thicknessing table chain, pay atten-

tion to the prallelism of the thicknessing table.

PLANER BLADES

The planer blades at work are beveled and setup correctly,

ready for use. Only well-sharpened and exactly set planer

blades can guarantee safe operation.

We recommend: Always keep a spare beveled planer blade

ready, in need of replacement. You can ﬁnd a spare planer

blade from your specialist Type Nr. 6200 4134.

Feed unit Fig. 13.2 – Warning!

The plastic cogwheels, chain wheels and chains and bolts

must be greased every 40 operating hours.

Beveling planer blades

Scheppach Plana 3.0 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info