Bedienungsanleitung Scheppach Plana 3.0 (Seite 16 von 128) (Alle Sprachen)

782085

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

english 15

Dull planer blades raise the risk of accidents, the work

efﬁciency is no longer guaranteed. Bevel the blade only

up to 15 mm knife height. The blade cutting angle should

avarage 40 ± 2 degrees.

For regrinding, bring the blade to an authorised grinding

workshop, or ship it back to the manufacturer.

Installing planer blades Fig. 16

1 Adjusting screw

2 Pressure screw

3 Planer blades

4 V-ledge

5 Markings

6 Adjust gauge

Make sure during installation that

• the risk of injury for ﬁngers and hands is mounted.

• the clamping surface in the cutter spindle and the

Vledge are clean.

• the beveled planer blades are deoiled.

• only blades that have been beveled in a pair are in-

stalled.

• the installation of the planer blades and the V-ledge

correspond to the illustration

• close the planer blades and the V-ledge on both sides.

• all of the clamping screws are tightened (8,9 N/m).

Warning! The details of blade fastening, blade pro-

tection length, blade thickness, should be kept for a

minimum during warm up spin and optimally for the

starting of the blade attachment screw.

Planer blade adjustment, Fig. 17

• To adjust, apply the provided adjustment gauges.

• First, adjust one blade, then the other.

• Shift the blade on the adjusting screw, alternating

sides, till the cutting edge that lies over the work ta-

ble touches the adjustment gauges.

• The right marking must align, corresponding to the il-

During spinning the planer blade must be in sync with

the adjustment gauges as much as possible, optimally

to the second marking.

• Left and right adjustment should be done following the

exterior of the blades.

• Tighten the pressure screws of the V-ledge with a ﬂat

wrench SW 8. (8,9 N/m)

• Adjust and clamp the second blade in the same way.

• Perform a test run after each blade change and then

retighten the pressure screws. (8,9 N/m)

The planer blade must be tested before use to make sure

that the above mentioned instructions have been followed.

Please be attentive of all the safety warnings before turn-

ing the machine on.

Declaration of compliance (EU)

Hereby we, the Scheppach Manufacture of Woodworking Machines

GmbH, Günzburger Str. 69, D-89335 Ichenhausen, declare that the

subsequent qualiﬁed machine by way of its construction and design

as well as commercial use meets the corresponding regulations of the

EG-guidelines stated below. In case of a modiﬁcation of the machine

this declaration is no longer valid.

The machine corresponds to the tested sample.

Name of the machine:

Thicknessing and Planing machine

Type of machine

Plana 3.0, Art.-Nr. 1902202901, 1902202902 , 1902202903

Relevant EC directives:

EC machine directive 2006/42/EG,

EC Low voltage directive 2006/95/EWG,

EC-EMV directive 2004/108/EWG.

Applied harmonized European standards:

EN 55014, EN 55104, EN 60555-2, EN 60204-1, EN 861, EN 847-1, EN

12100-2

Notiﬁed body:

Technical Committee on Wood, 70504 Stuttgart; Checking and certifying

body BG-Approval certiﬁcate

Place, Date:

Ichenhausen, 28.03.2012

Signature:

Werner Hartmann (Head of technical Innovation - documentation repre-

sentative)

Trouble shooting

To repair faults, switch off the machine. Pull power plug.

Problem Possible Cause Relief

Irregular and discontinuous transport

at the thickness planing

Thickness desk not free of resin or

not free of oil.

Clean and spray (sliding spray) the

thickness desk regularly. This is

valid especially for wet and resinous

woods.

Workpiece shoulder at the planing This is due to badly adjusted planer

knives.

The adjustment of the planer knives

has to be carried out with a lot of

care with help of the adjustment

gauge.

Workpiece inaccuracy at the planing

(concave, convex)

At not exactly parallel standing

trimming desks due to improper

transport or similar.

Adjust the stiff trimming desk 1 mm

above the planing shaft body, as well

as parallel to the bottom plate.

Electrotechnical maintenance only by electric specialists!

At waste disposal of the machine all the local legal regulations have to be kept.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach Plana 3.0 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info