Bedienungsanleitung Scheppach Plana 4.1C (Seite 18 von 88) (Deutsch, Englisch, Holländisch, Französisch, Finnisch)

782090

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

11. Secure work

• Use clamps or a vise to hold work. It‘s

safer than using your hand and it frees

both hands to operate tool.

12. Don‘t overreach

• Keep proper footing and balance at all

times.

13. Maintain tools with care

• Keep tools sharp and clean for better

and safer performance. Follow instruc-

tions for lubricating and changing acces-

sories. Inspect tool cords periodically

and, if damaged, have repaired by au-

thorized service facility. Inspect exten-

sion cords periodically and replace if

damaged. Keep handles dry, clean and

free from oil and grease.

14. Disconnect tools

• When not in use, before servicing, and

when changing accessories such as

blades, bits and cutters.

15. Remove adjusting keys and wrenches

• Form the habit of checking to see that

keys and adjusting wrenches are re-

moved from tool before turning it on.

16. Avoid unintentional starting

• Don‘t carry plugged-in tool with nger on

switch. Be sure switch is off when plug-

ging in.

• Never leave a running machine unat-

tended. Before you leave the workplace

switch off the machine.

17. Outdoor use extension cords

• When tool is used outdoors, use only ex-

tension cords intended for use outdoors

and so marked.

18. Stay alert

• Watch what you are doing. Use common

sense. Do not operate tool when you are

tired.

• Do not operate the machine under the

inuence of drugs, alcohol or any medi-

cation. Be aware that medication can

change your behaviour.

19. Check damaged parts

• Before further use of the tool, a guard

or other part that is damaged should

be carefully checked to determine that

it will operate properly and perform its

intended function. Check for alignment

of moving parts, binding of moving

parts, breakage of parts, mounting, and

any other conditions that may affect its

operation. A guard or other part that is

damaged should be properly repaired or

replaced by an authorized service cent-

er unless otherwise indicated elsewhere

in this instructions manual. Have defec-

tive switches replaced by an authorized

service center. Do not use tool if switch

does not turn it on and off.

20. Warning

• The use of any other accessory or at-

tachment other than recommended it

this operating instruction or the Einhell

catalog may present a risk of personal

injury.

21. Have your tool repared by an expert

• This electric appliance is in accordance

with the relevant safety rules repairing of

electric appliances may be carried out

only by experts otherwise it may cause

considerable danger for the user.

22. Connect the dust extraction devic

• Wherever there are facilities for tting a

dust extraction system, make sure it is

connected and used.

Additional safety instructions

Do not use blunt knives. Risk of kick-back.The

cutter block must be fully covered.

Use a push stick to plane any short workpiec-

es.Take additional safety precautions if you

are planingany narrow workpieces. It may be

necessaryto use lateral pressure equipment

and springloadedcovers to ensure that you

can work insafety.

The machine is not suitable for cutting re-

bates.The anti-kick safeguard and the infeed

roller mustbe inspected at regular intervals.

Machines tted with a sawdust extractor an-

dextractor hoods must be connected to the

devices concerned. The type of material used

can have a negative inuence on the dust gen-

erated.

The machine is designed exclusively for the

cutting of wood and similar materials.

The knife must be replaced immediately once

it becomes worn down by 5%.

If a push stick is not used there may be a risk of

serious danger. The push stick should always

be kept at the point provided on the left-hand

side of the machine when not used.

There is a greater risk of danger when small

workpieces are fed in by hand. Always ob-

serve the manufacturerʼs instructions on the

use of the push stick.

If the safety covers, infeed table or mesh are

incorrectly aligned they could lead to uncon-

trollable situations. Damaged or soiled work-

pieces may cause a risk of danger. Never use

metal parts in the machine or any materials

which can fracture or shatter.

Risk of injury! To cut long workpieces, always

place them on a mobile table or similar type

of supporting equipment. Otherwise there is a

risk that you may lose control over the work-

piece. The machine is only suitable for planing

and thicknessing.

Wear suitable protective clothing when work-

ing with the machine.

• ear protection to prevent damage to your

ears,

• a breathing mask to avoid the risk of inhaling

hazardous particles of dust,

• safety gloves to avoid injuries from sharp

edges or knives,

• safety goggles to avoid eye injuries from y-

ing parts.

It is imperative that the following situations are

avoided at all times: Premature interruption

of the cutting operation (planing cuts which

do not complete the entire length of the work-

piece; planing of uneven pieces of wood which

do not lie at on the infeed table). The machine

is designed for private use only. It is prohibited

to use the machine for professional or com-

mercial use. Residual risk: Bear in mind that

there is always the possibility of residual risks

associated with the use of the machine even if

you comply with all the safety instructions. By

complying with these instructions and taking

suitable care when using the machine you will

reduce the risk of injury or of damage to the

machine. Particular risks:

• Injuries to ngers or hands from parts of

the machine or from workpieces, e.g. when

changing the planing knife

• Risk of electric shock if you use power con-

nections which do not comply with stand-

ards

• Contact with conductive parts on opened

electrical components

• Hearing impairments if you work for lengthy

periods without ear protection

• Emission of hazardous sawdust if a dust ex-

tractor is not used.

Even if all safety precautions are complied

with it is still possible for some residual risks

to remain.

Important! If the primary mains connection

is in a poor condition there is a risk of short-

circuits when the machine is switched on. This

may also affect other functions (e.g. the light-

ing up of indicator lamps). Should there be any

faults in the primary mains connection (max.

current impedance < 0.105 Ω), please contact

your local electricity supplier to advice and in-

formation.

If the blade is fastened and positioned incor-

rectly this may result in the blade being ung

out, which may be a cause of danger. There-

fore, before operation, make sure that the

blade is correctly tted and adjusted in accord-

ance with the operating instructions. Every

part of the blade shaft not used for planning

must be covered.

Check the machine and carry out required

maintenance work on it each time before you

start it up. In particular, inspect all the anti-kick

claws and the infeed drive shaft.

Make sure that the dust extraction system and

collector are connected and are used correct-

ly. Make sure that the dust extraction system is

suitable. Fine sawdust may not only be harm-

ful to health, in certain concentrations it can

also be potentially explosive. Always switch off

the machine and pull out the mains plug before

making any adjustments or changing settings.

Sawdust may cause risks to health.

Please keep these safety instructions in a

safe place.

Scheppach Plana 4.1C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info