Bedienungsanleitung Scheppach Plana 4.1C (Seite 21 von 88) (Deutsch, Englisch, Holländisch, Französisch, Finnisch)

782090

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

• Dressing: When dressing up to a 100 mm

width work piece, the cutterblock cover has

to cover the work piece and the cutterblock

from the top. If the work piece is wider than

100 mm, set the guard rail of the cutterblock

cover to the width of the work piece. Make

sure you put the at of the hand with all ve

digits together and extended on the work

piece.

• Joining: The work piece is positioned

against the jointing fence. Set the guard rail

of the cutterblock cover to the width of the

work piece and place it on the table.

• Dressing and joining of small cross sections

(slats): During dressing, the work piece is

pushed forwards with hands sitting at on

it, as is the case with work pieces up to a

width of 100 mm. During joining, the work

piece is pushed against the stop with both

hands, sts closed, and pushed forwards.

The guard is positioned at the fence and lies

on the work piece.

• Dressing and joining of short work pieces

(min. length 150mm): During dressing, the

work piece is pressed on the loading table

with a at hand and pushed forwards with

the push block guided by the right hand. The

left hand glides over the guard. As soon as

the work piece lies on the unloading table,

the pressure from the left hand is changed

to the unloading table. During joining, the

work piece is pressed against the fence and

the table with the left hand, st closed, and

pushed forwards with the push block.

• Chamfering or bevelling: The work piece is

positioned against the jointing fence. Set

the guard rail of the cutterblock cover to the

width of the work piece and place it on the

table. The work piece is pressed against the

fence and the unloading table with the left

hand, st closed, and pushed forwards with

the closed right hand.

• Warning! Never work with a jointer without

the cutterblock cover.

Electric connection m

• Check the mains connection cables. Do not

use faulty cables. See Electric connection.

• Observe the rotational direction of the mo-

tor and the tools, see Electric connection

planer.

• Installations, repairs and maintenance on

the electric installation may be carried out

only by experts.

• Turn the machine off when resolving issues.

Disconnect the mains plug.

• Turn the motor off when you leave the work

place. Disconnect the mains plug.

• Disconnect the machine from every exter-

nal energy supply even for slight changes of

position! Connect the machine to the mains

again before using it!

Connect the machine to the mains with a CEE-

plug, the supply line has to be protected with

16 A.

On the operating switch, press the green push

button, the cutterblock starts up (g. 14).

To turn it off, press the red push button, the

cutterblock stops within 10 sec.

Change of rotational direction

When connecting the machine to the mains

or changing its position, the rotational direc-

tion has to be checked. The polarity has to be

swapped, if applicable, using a screw driver

(machine socket g. 15).

The installed electric motor is connected and

operational. The connection complies with rel-

evant VDE and DIN stipulations. The mains

connection at the customer’s as well as the

extension lead used have to comply with these

stipulations or the local EVU-stipulations.

Duration of use / duty cycle

The electric motor is for operating type S1 for

continuous operation.

When there is an overload, the motor turns it-

self off because a winding thermostat is inte-

grated in the motor development. After a cool-

down period (timing varies), the motor can be

turned on again.

Hazardous electric connections

Insulation damage often occurs on electric

connections.

Possible causes:

• Pressure marks when connections are guid-

ed through windows and doors

• Kinks due to inappropriate attachment or

guidance of the connection

• Cuts when the connection is run over

• Insulation damage when being pulled out of

the wall socket

• Tears from ageing insulation. Such hazard-

ous electric connections must not be used

and are dangerous to life due to the insula-

tion damage.

Regularly check electric connections for dam-

age. Make sure the connection is not con-

nected to the mains when checking. Electric

connections must comply with relevant VDE

and DIN stipulations and the local EVE stipula-

tions. Only use connections marked H 07 RN.

Printing the type designation on the connec-

tion is the law.

Extension leads up to 25 m in length must

have a cross section of 1.5 mm2, at more than

25 m length, it has to be at least 2.5 mm2.

The mains connection is protected against

short circuit with a 16 A slow fuse.

Three-phase motor

The power voltage has to be 380÷420 V 50 Hz.

Mains connection and extension leads have to

be 5 core =3 P + N + SL.

Extension leads must have a minimum cross

section of 1.5 mm².

The mains connection is protected against

short circuit at a maximum of 16 A.

When connecting the machine to the mains

or changing its position, the rotational direc-

tion has to be checked. The polarity has to be

swapped, if applicable, using a screw driver

(machine socket g. 15).

One-phase motor

The power voltage has to be 230 V 50 Hz.

Connections and repairs to the electrical

equipment may be carried out only by a trained

electrician.

If there are any questions, please provide the

following data:

• Motor manufacturer; motor type

• Motor’s type of power

• Data from the machine’s type plate

• Data from the electronic control

When sending back the motor, always send

the entire motor unit with electronic control.

Maintenance

mWARNING

Before working on the power tool itself (e.g. transport, set-up, re-tooling, cleaning and maintenance), disconnect the mains

plug from the socket!

■ CLEANING

Carry out maintenance, service and repairs

as well as malfunctions only when the motor

is turned off. Turn the machine off via the off-

switch, then disconnect the mains plug!

All protective and safety equipment must be

re-attached immediately after completing re-

pairs and maintenance.

Always keep the jointer tables and the thick-

nessing table free from resin. The bearings

of the cutterblock are permanently lubricated.

Warmth occurring when the machine is in a

new condition is due to construction and will

disappear with time.

Clean the feed rollers regularly.

Scheppach Plana 4.1C Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info