Bedienungsanleitung Scheppach SG3400i (Seite 25 von 120) (Deutsch, Englisch, Französisch, Italienisch)

781618

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 25

• Drain the used oil into a suitable collection container.

• Finally, re-assemble everything in reverse order.

• When lling the new oil, bear in mind that you

should not ll the recommended quantity of oil at

once, as small quantities of oil always remain dur-

ing an oil change.

• Check the oil level as described in the “Checking

the oil level” point.

• Dispose of the oil in accordance with stipulations.

Take the old oil to a collection point. Most petrol

stations, garages or recycling centres take back old

oil free of charge.

Air lter

Frequently cleaning of the air lter prevents carbu-

retor malfunction. Clean the air lter regularly, espe-

cially when working in dusty environments.

Clean the air lter

• The air lter should be cleaned every 30 hours.

.(When working in a dusty environment, the air lter

should be cleaned after work is complete).

• Remove the cover (10a) (Fig. 10 - 11)

• Remove the air lter cover, by loosening the two

screws (12a & 12b). (Fig. 12).

• Remove the lter element.

• Clean the lter element with soapy water. After

rinse the lter element with clear water and allow to

dry thoroughly before retting.

• Reassemble in reverse order

m WARNING

NEVER use gasoline or cleaning solvents with a low

ash point to clean the air lter element. A re or ex-

plosion could result.

Note

Never run the engine without or with a damaged air

lter. Dirt gets so into the engine, causing serious

engine damage can occur. In this case, seller, and

manufacturer disassociate from any warranty.

Check, clean and replace spark plug

Check the spark plug after 10 hours on dirt and grime.

If necessary, clean it with a copper wire brush. Main-

tenance the spark plug after 50 hours of operation

• Open the cover (10a) (Fig. 10)

• Remove the ignition cable with plug. (Fig. 13)

• Remove any dirt from the base of the spark plug.

• Use the enclosed spark plug spanner (E) to remove

the spark plug.

• Check the spark plug visually. Remove any debris

with a wire brush.

• Look for discoloration on the top of the spark plug.

By default, the color should be bright.

• Check the spark plug gap. An acceptable gap width

is 0.6 to 0.7 mm (Fig. 14)

• Remove the spark plug carefully by hand.

8.4 Electrical safety

Electrical cables and attached devices must be de-

fect free.

Never connect the generator to the mains (power

point).

Keep the cables as short as possible.

8.5 Connecting to earth

The housing can be connected to earth to discharge

static electricity. To do this, connect one end of a ca-

ble to the earthing connection (3) on the generator

and the other end to an external ground (z. B. for ex-

ample to an earthing rod).

8.6 12 V Connection

At the 12 V DC connection (14), a 12 V battery can be

charged using the included cable (A).

8.7 Reset button (12)

If the overload protection was triggered and the over-

load indicator light illuminates red, the reset button

can restore the generator‘s output power; as a result,

the engine does not need to be restarted completely.

Press and hold the “RESET” button for 1 second until

the light (red) is extinguished and the operation indi-

cator light (green) illuminates. If the overload protec-

tion was not triggered, the reset button does not have

any effect.

8.8 Display button (13)

You can use the display button to alternate between

displaying the following data

-Engine speed

-Engine run time in hours and minutes

- Volt + Hz

The display switches off automatically after around

20 seconds when not used

9. Maintenance

m WARNING

• Carry out maintenance work only with the stopped

engine.

• Pull the spark plug cap from the spark plug

Oil change (Fig. 6, 8 & 9)

Change the engine oil after 25 operating hours, then

after 50 hours or every three months.

The engine oil change should take place when the

engine is at operating temperature.

• When changing the oil, have a non-leaking con-

tainer available.

• Remove the cover (6) (Fig. 6)

• Undo the screw (8a); push the cable to the side so

that it does not get coated with oil.

• Then loosen the rubber stopper (9a) (Fig. 8 - 9) and

remove the dipstick.

• Then open the oil drain screw (9b) (Fig. 9)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach SG3400i Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info