Bedienungsanleitung Scheppach TKG 210-30 (Seite 14 von 26) (Deutsch, Englisch)

782518

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Assembly and Operation

Before first Use

Take the bench saw and all accessory parts out of the package. As transport protection a

Styrofoam block is wedged in the machine. Remove it before setting up the machine.

Please make sure all parts are present.

Dispose of packaging materials or store it out of reach of children. Plastic bags etc. may become a

deadly toy for children.

Start-Up

1. During operation the bench saw must be solidly attached to a firm and even surface. If the

machine is just placed on a workbench and not attached, it might move during operation.

2. The machine is delivered with three additional supports. The two lateral work piece supports

are inserted into the holes on the sides and the rear support is inserted from the rear with the

angled portion facing down. Secure the supports with the clamping screws.

3. Before connecting the machine to the power mains, please make sure the mains voltage in

your area corresponds to the operating voltage stated on the type label. If you are using a

cord reel as an extension cord, please roll the cord off the reel completely, because

otherwise the coiled cable on the reel may overheat and become damaged.

ON/OFF Switch (1)

To turn the machine ON, push the green button and to turn off the machine, press the red button.

The ON/OFF switch is a safety switch with low voltage circuit breaker. The construction of the

switch makes sure that the machine will not accidentally restart after power failure.

Dust Extraction

On the back side of the housing is the dust extraction flange. With a suitable adaptor you can

connect the dust bag, a dust extractor or a vacuum cleaner. Do not use the saw without some kind

of dust catching or dust extraction system.

Converting the Saw

Before converting the saw disconnect it from the power supply!

The convert the saw from a table saw to a crosscut and metre saw loosen the

turnknobs (15) and set the table to the highest position. Lock the table in place with the turnknobs.

Lightly press down the upper part of the saw by the handle and pull out the retaining pin (17).

Allow the upper part of the saw to swing up and take out the Protective tub (19).

To convert the saw from a crosscut and mitre saw to a table saw set the cutting angle along both

axes exactly to zero. Place the protective tub (19) on the turn table and hook it into the fence.

Press the unlocking button (2) and push down the upper part of the saw and hold it in the lowest

position. Push the retaining pin (17) in to secure the upper part. Loosen the turnknobs (15) and set

the table to the lowest position and secure it by tightening the turnknobs.

Operation as a Crosscut and Mitre Saw

Set the machine up as a crosscut and mitre saw as described above in the chapter “Converting

the Saw”.

When using the machine a mitre saw, set the cutting angle along both axes. To do so, loosen the

turnknob (6) and turn the rotatable table until the indicator on the forward degree scale is set to

zero. Secure the rotatable table by tightening the turnknob. Loosen the turnknob (18) and set the

mitre angle using the rear scale. Secure the upper part of the saw by tightening the turnknob.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TKG 210-30 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info