Bedienungsanleitung Scheppach TKG 210-30 (Seite 15 von 26) (Deutsch, Englisch)

782518

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Assembly and Operation

Secure the workpiece with the clamp (4). Carefully stay away from the spinning saw blade. Make

sure the saw blade can not touch any of the fences and adjust the fences if necessary.

If you intend to cut a curved work piece, make sure

the work piece is not bent against the fence. Make

sure no gap forms between the work piece, the

fence and the base plate.

Long workpieces must be supported in a suitable

way, e.g. on a support equipped with rollers. Avoid

holding or guiding workpieces in a way which

compromises your balance.

To cut, operate the ON/OFF switch (1) before

pressing down the upper part of the saw. When the

machine has reached full speed, press the locking

button (2) and press down the upper part of the saw by the handle. Whenever possible, cut

through the workpiece with a single, even motion. Irregularly shaped workpieces can cause the

upper part to kick back up unexpectedly, therefore hold the handle with a firm grip.

Operation as a Table Saw

Set the machine up as a table saw as described above in the chapter “Converting the Saw”.

When using the machine as a table saw, always set the table to the lowest position. The table is

equipped with a scale for positioning the parallel fence (12). The parallel fence is fixed in place

with the knobs. The upper safety hood lifts automatically when a workpiece is pushed under it.

Operate the ON/OFF switch (1) and allow the machine to rev up to full speed before you start

cutting. Move the workpiece at an even pace with moderate speed over the table. Long

workpieces must be supported in a suitable way, e.g. on a support equipped with rollers. Avoid

holding or guiding workpieces in a way which compromises your balance.

Using the Push Stick (13)

When working on narrow or small workpieces, there is a danger of touching the spinning saw

blade with your hand. This will inevitably lead to severe injury. For this reason a push stick has

been included with the machine. Use it to push small workpieces against the saw blade. While the

push stick is not used, it should be stored on the machine. It can be snapped into the two clips on

the right side of the table.

Changing the Saw Blade

Damaged saw blades must be replaced immediately. Before undertaking any work on

the machine, pull the power plug and always wear working gloves when handling the

saw blade!

1. To change the saw blade, set the machine to crosscut and mitre saw and raise the arm to the

highest position.

2. Loosen the retaining screw (16) of the operating lever of the safety hoods and open the

hoods to gain access to the saw blade.

Please keep in mind that even a worn saw blade is still sharp!

Always wear gloves when handling it!

3. The saw blade is fixed on the drive shaft with an inner and an outer flange. In front of the

outer flange a screw is screwed into the shaft to tension the flanges. Between screw and

flange there is a flat washer.

right

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach TKG 210-30 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info