Bedienungsanleitung Seagate BlackArmor Back-up (Seite 125 von 130) (Englisch)

468758

125

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

It is also possible that the device is out of order, or the hard disk is not formatted.

B.3 Installing a SATA hard drive

Most recently manufactured PCs use the SATA interface for hard drives. In general,

installing a SATA hard drive is easier than an IDE drive, as it is not necessary to

configure master-slave jumpers. SATA drives use a thin interface cable with seven-

pin keyed connectors. This improves airflow through the PC case. Power is supplied

to SATA drives through 15-pin connectors. Some SATA drives also support legacy

four-pin power connectors (Molex) — you can use a Molex or SATA connector but

do not use both at the same time, because this could damage the hard drive. You'll

also need a free power lead fitted with a SATA power connector. Most systems that

come with SATA ports have at least one SATA power connector. If this is not the

case, you will need a Molex-to-SATA adapter. In case your system has the SATA

power connector but it is already occupied, use a Y-adapter that splits a lead in two.

B.3.1 Steps for installing a new internal SATA drive.

1. Find an unused SATA port using the documentation provided with your PC. If you

are going to connect your new SATA drive to a SATA controller card, install the

card. If you are going to connect the SATA drive to the motherboard, enable

applicable motherboard jumpers, if any. Most hard drive kits include a SATA

interface cable and mounting screws. Attach one end of the SATA interface cable to

a SATA port on the motherboard or interface card, and the other to the drive.

2. Then plug the power-supply lead or use a Molex-to-SATA adapter.

3. Prepare your drive. If you're installing a SATA 300 hard drive, check your PC's (or

SATA host adapter's) documentation to make sure it supports SATA 300 drives. If it

doesn't, you might need to change a jumper setting on the drive (see the drive's

manual for instructions). If you have a SATA 150 hard drive, you don’t need to

change any settings.

4. Turn on the PC and look for the new drive in the boot-up messages. If you don't

see it, enter the PC's CMOS setup program and search the BIOS configuration menu

for an option that will let you enable SATA for the ports you are using (or maybe

you will just need to enable SATA). See your motherboard documentation for

instructions specific to your BIOS.

5. If the operating system does not recognize the SATA drive, you need the

appropriate drivers for your SATA controller. If the drive is recognized, go to step 8.

Usually, it is best to obtain the latest driver version from the motherboard or

SATA controller manufacturer's website.

If you download a copy of the SATA controller drivers, place the driver files to a

known location on your hard drive.

6. Boot from the old hard drive.

The operating system should detect the SATA controller and install the

appropriate software. You might need to provide the path to the driver files.

7. Ensure that the SATA controller and the connected SATA hard drive are correctly

detected by the operating system. To do this, go to the Device Manager.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seagate BlackArmor Back-up Seite 125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info