Bedienungsanleitung Seat Ateca 2024 (Seite 333 von 377) (Englisch)

817353

333

Zoom out

Zoom in

Vorherige Seite

1/377

Nächste Seite

Wheels and tyres

331

Changing a wheel

WARNING

If the wheel bolts are not properly tightened,

they could come loose while driving and

cause an accident, serious injury and loss of

vehicle control.

● Use only wheel bolts which correspond to

the rim in question.

●Never use dierent wheel bolts.

●Wheel bolts and threads should be clean,

free of oil and grease, and it should be possi-

ble to screw them easily.

● To loosen and tighten wheel bolts, only

use the wheel wrench that came with the car

from the factory.

●The wheel bolts should only be loosened

slightly (about one turn) before raising the

vehicle with the jack. Risk of accident!

●Never apply grease or oil to wheel bolts or

to the wheel hub threads. Even if the bolts

have been tightened to the prescribed tor-

que, they could come loose while driving.

●Never loosen the screwed joints of wheel

rims with bolted ring trims.

●If wheel bolts are tightened below the

prescribed torque, the bolts and rims could

come loose while driving. If tightening torque

is too high, the wheel bolts or threads can be

damaged.

Raise the vehicle

Fig.228 Jack position points.

Fig.229 Crossbar: mounting the jack on the

vehicle.

●Rest the jack (vehicles tools) on ﬁrm ground.

If necessary use a large, strong board or similar

support. If the surface is slippery (for example

tiles) place the jack on a rubber mat or similar

to prevent it from slipping ››› .

●Look on the strut for the mark of the jack sup-

port point (sunken area) closest to the wheel to

be changed ›››Fig.228.

●Turn the jack crank handle, located below the

strut support point, to raise it until the tab 1

›››Fig.229 is below the housing that is provi-

ded.

● Align the jack so that the tab 1 “grips” onto

the housing provided on the cross member and

the mobile base 2 is resting on the ground. The

base plate 2 should fall vertically with respect

to the support point 1 .

●Continue turning the jack until the wheel is

slightly lifted o the ground.

WARNING

The factory-supplied jack is only designed

for changing wheels on this model. On no

account attempt to use it for lifting heavier

vehicles or other loads. Risk of injury.

● Make sure the jack remains stable. If the

surface is slippery or soft, the jack could slip

or sink, respectively, with the consequent risk

of causing injuries.

● Lift the vehicle using only the jack supplied

from the factory. Other jacks, even those ap-

proved for other SEAT models could slip, with

the consequent risk of injury.

●Place the jack only at the support points

provided on the strut and align it. Otherwise,

the jack could slip because it does not have

sucient grip on the vehicle: risk of injury!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seat Ateca 2024 Seite 333

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seat Ateca 2024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info