Bedienungsanleitung Seiko V192 Diver (Seite 7 von 17) (Englisch)

757543

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

How to use the rotating bezel

By setting the rotating bezel beforehand, the elapsed time since the start of an event can be measured.

Example: When you start diving at 10:10 am.

Align the mark

with the minute hand

Rotating direction of

the bezel

Example: After 20 minutes has elapsed

Elapsed time

* The above illustration is provided as an example, therefore it may not be exactly the same as your watch.

1At the start of the event, for which

you want to measure the elapsed

time (for example, when you start

diving), rotate the bezel so that

the mark on the bezel is

aligned with the minute hand.

The rotating bezel is designed to rotate only

counterclockwise.

Do not forcibly rotate it clockwise.

“[One-Way rotating bezel]” → P. 21

2Read the graduation on the

rotating bezel to which the

minute hand is pointing.

The graduation on the rotating bezel to

which the minute hand is pointing indicates

the elapsed time.

EN 20

HOW TO USE

[One-Way rotating bezel]

As the evaluation of the remaining air in your cylinder is based on the information of the elapsed time of the dive,

the rotating bezel for a diver’s watch is designed to rotate only counterclockwise, so that the watch is prevented

from displaying the elapsed time shorter than it actually is.

bCAUTION

Make sure that you check the correct remaining amount of air in your cylinder before diving.

Use the display of the elapsed time by the rotating bezel only as a guide during diving.

EN 21

HOW TO USE

How to set the time and date

■ How to set the time and date

* When setting the date only, refer to “Manual date adjustment at the end of the month” → P. 25.

1Make sure that the watch is working.

Check that the small seconds hand is moving every second.

If it is moving every two seconds or has stopped, expose the dial to light to charge the watch. “Charging

the battery” → P. 33

2Check that the watch hands are not displaying any time between 9 p.m. and 1

a.m.

If a time between 9 p.m. and 1 a.m. is being displayed, pull the crown to the second click, advance the

hands beyond the 1 a.m. position, and push the crown back in.

* This procedure is required to ensure the proper engagement of the date driving wheel.

* Each time the hour hand makes two full rotations, the date is adjusted by “one day”. While turning the crown,

the moment the date changes is midnight. Use the 24-hour hand to check whether the displayed time is a.m./

p.m. “Names of the parts and their functions” → P. 16

EN 22

HOW TO SET THE TIME AND DATE

Pull out the crown to the first

click

4The date can be set by turning the crown.

Turn it until the previous day’s date appears.

Ex.) To display the date as “6,” then set this to “5.” Turn the crown to the right (clockwise) to set the

date.

3Pull out the crown to the first click.

The small seconds hand will continue to move.

* For models with screw down crown, please unlock the

crown before operating it.

EN 23

HOW TO SET THE TIME AND DATE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Seiko V192 Diver Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Seiko V192 Diver

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info