Bedienungsanleitung Sekonic L-508 (Seite 10 von 16) (Englisch)

528681

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

5. Measurement

2-2 Auto-reset cordless flash mode

Measurements are made by the meter receiving the light from the flash. This measurement

mode is used when the Synchro cord will not reach because of the distance between the

flash and meter or when use of the Synchro cord is inconvenient.

2. Turn the Set/change dial to set shutter speed.

When setting shutter speed, first check the

settings to confirm that they correspond to the

settings available on the camera.

4. If the 90 second period is exceeded and the blinking mark stops, press the Measuring

button again to return to ready to measure.

NOTES:

• If the shutter speed is changed after measurement, the measure (f stop) is cleared to 0

and you must take the measurement again.

• When firing a flash, if the flash brightness is low compared to the ambient light, the

meter may fail to detect the light. In this case, make measurements using the flash with

cord mode.

• Rapid start fluorescent lamps and special lighting are sometimes mistaken for flash, and

accidentally measured. In this case, make measurements using the flash with cord

mode.

• The meter's tripod socket permits mounting it to a tripod or light stand and placing it

strategically when using cordless flash mode.

-15-

5. Measurement

Reference:

• Setting the shutter speed is the same as measurement (see page 14) of "Flash mode

with cord" of section 2-1 .

• A new converted value is displayed when the film speed is changed after taking the

measurement.

• Readings over and under the measuring range are the same as measurement (see

page 14) of "Cord Flash mode" of section 2-1 .

2-3 Cord multiple flash (cumulative) mode

These measurements are used when the light generated by the flash is inadequate for proper

exposure. The repeated flash pops can be accumulated until the desired aperture is displayed.

The accumulation can be repeated up to nine times.

1. Slide DIP switch to MULTI (see page 8) to the ON

position.

Hold down the Mode set button 10 and turn the

Set/change dial 5 to select flash measurement

with cord cumulative mode (MLT will display on

the LCD).

2. Turn the Set/change dial 5 to set shutter speed. When setting shutter speed, first check

the settings to confirm that they correspond to the settings available on the camera.

3. Connect the Flash synchro cord to the meter's

synchro terminal 8.

4. Press the Measuring button 19 to trigger a flash. The measured f stop value at that time

will be displayed. Each time this is repeated, the accumulated f stop value and the

number of cumulative flashes is displayed.

CAUTION:

• There is danger of electric shock if the meter is handled with wet hands, during rain, in

areas splashed by water or where there is a lot of moisture.

Under such conditions, it is recommended that you use the meter in the flash cordless

mode, and keep the Synchro terminal cap in place.

-16-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sekonic L-508 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sekonic L-508

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info