Bedienungsanleitung Sekonic L-508 (Seite 11 von 16) (Englisch)

528681

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

5. Measurement

NOTE:

• The flash unit may flash when you connect the synchro cord or operate the POWER

switch.

• When firing a flash to make measurements, check the camera's synchronizing range

and set the proper shutter speed.

• For flash units with low electric trigger voltage, the flash may not fire. In this case, make

measurements in flash mode without cord (see page 15).

• A new converted f stop is displayed when the film speed is changed after taking the

measurement.

• If the shutter speed is changed after measurement, the number of cumulative flashes

and the f stop value are cleared to 0 and you must take the measurement again.

Reference:

• Setting the shutter speed as measurement (see page 14) of "Flash mode with cord" of

Section 2-1.

• Readings over and under the measuring range, are the same as measurement (see

page 14) of "Flash mode with cord" of section 2-1.

2-4 Cordless flash cumulative mode

These measurements are used when the light generated by the flash is inadequate for proper

exposure. The repeated flash pops can be accumulated until the desired aperture is displayed.

The accumulation can be repeated up to nine times.

1. Slide DIP switch to MULTI (see page 8) to the ON

position.

2. Hold down the Mode set button 10 and turn the

Set/change dial 5 to select flash measurement

without cord cumulative measurement mode. (MLT

will display on the LCD).

Turn the Set/change dial to set shutter speed. When

setting shutter speed, first change the settings to

confirm that they correspond to the settings available

on the camera.

3. When the light from the flash is received, the measured value (f stop) is displayed. Each

time this is repeated, the accumulated value for the aperture and the number of

cumulative flashes is displayed.

-17-

5. Measurement

4. The ready to measure mode will be displayed for approximately 90 seconds. If the 90

second period is exceeded and the blinking mark stops, press the Measuring button 19

again. The measured value (f stop) of the previous time reverts to 0 and the meter is in

ready to measure mode.

NOTE:

• If the shutter speed is changed after measurement, the (f stop) value and the number

of cumulative flashes are cleared to 0 and you must take the measurement again.

• When firing a flash, if the flash brightness is low compared to the ambient light, the

meter may fail to detect the light. In this case, make measurements using the flash

with cord mode.

• Rapid start fluorescent lamps and special lighting are sometimes mistaken for flash

and accidentally measured. In this case, make measurements using the flash with

cord mode.

Reference:

• Setting the shutter speed is the same as measurement (see page 14) of "Flash mode

with cord" of Section 2-1.

• "E.u" (Exposure under) or "E.o" (Exposure over) appears when the combination of

shutter speed and aperture is not possible for the measured light level. Change the

shutter speed with the Set/change dial and take measurements again.

• If the "E.u." or "E.o" readout blinks, this indicates that the light level is beyond of the

measurement range of the light meter.

-18-

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sekonic L-508 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sekonic L-508

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info