Bedienungsanleitung Sencor SCP 3701 (Seite 6 von 6) (Englisch)

759014

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

- 6 - 03/2020

Overheating protection

■ The appliance is equipped with overheating protection. In the event that there

is arisk of it overheating (you placed an empty pot or pan on the hotplate), the

appliance will beep and turn off automatically.

Note:

For safety reasons, the cooktop will turn off automatically after two hours

of operation if you do not press any button or adjust the settings.

CLEANING AND MAINTENANCE

■ Clean the appliance after every use. Makes sure that dried on food or other residues

do not accumulate on it. Before cleaning it, always turn off the appliance using the

On/Off button B12, disconnect the power cord from the power socket and allow the

appliance to cool down completely.

■ To clean the hotplate A2 and the surface around it, use asoft, lightly dampened

textile. Then wipe the hotplate A2 dry. In the event of greater soiling, use asmall

amount of neutral kitchen detergent. Remove any remaining detergent using

aclean, lightly dampened cloth. Then thoroughly wipe the cleaned surface until dry.

■ Do not use steel wool, solvents, cleaning products with an abrasive effect, etc. to

clean the appliance. Otherwise the surface coat of the appliance may be damaged.

Warning:

To prevent the risk of injury by electrical shock, do not submerge

the appliance, power cord or power plug in water or any another

liquid.

Storage

■ When not using the appliance for an extended period of time, disconnect the power

plug from the power socket, allow the appliance to cool down and clean it according

to the instructions provided above. Before storing it, check that the appliance is

clean and dry. Store the appliance in adry, clean and well-ventilated location not

exposed to extreme temperatures and out of children'sreach.

Error messages

Error code Cause Solution

E0 There is no pot

or pan on the

hotplate A2, or you

placed unsuitable

cookware on it.

Use suitable cookware – more in section

"Induction and selecting suitable

cookware".

E1 or E2 Heat sensor error. Stop using the appliance, disconnect the

power plug from the power socket and

contact an authorised service centre.

E3 or E4 The voltage in the

power socket to

which the cooktop

is connected is too

high or too low.

Insert the power plug into apower socket

with avoltage of 220 – 240 V~.

E5 Overheating Allow the cooktop to cool down. Then put it

into operation again.

E6 The heat fuse was

activated, the

cooktop turned off

due to overheating.

Allow the cooktop to cool down. Check that

the air inlet A1 and the fan and the air outlet

A3 are free and unobstructed. If the problem

persists, stop using the appliance, disconnect

the power plug from the power socket and

contact an authorised service centre.

Note:

If the problem persists, stop using the appliance, disconnect the power

plug from the power socket and contact an authorised service centre.

TECHNICAL SPECIFICATIONS

Rated voltage range ....................................................................................................... 220 – 240 V~

Rated frequency......................................................................................................................50 / 60 Hz

Rated power input .................................................................................................................... 2,000 W

Hotplate power settings ..............................................................................................200 – 2,000 W

Hotplate temperature settings .......................................................................................60 – 240°C

Operating time settings ..........................................................................................1 – 180 minutes.

Safety class for electrical shock protection: Class II – Electrical shock protection

is provided by double or heavy-duty insulation.

We reserve the right to change the text and technical specifications

INSTRUCTIONS AND INFORMATION REGARDING THE

DISPOSAL OF USED PACKAGING MATERIALS

Dispose of used packaging material at asite designated for waste in your municipality.

DISPOSAL OF USED ELECTRICAL AND ELECTRONIC

EQUIPMENT

This symbol on products or original documents means that used

electric or electronic products must not be added to ordinary

municipal waste. For proper disposal, renewal and recycling, hand

over these products to determined collection points. Alternatively, in

some European Union states or other European countries you may

return your appliances to the local retailer when buying an equivalent

new appliance.

Correct disposal of this product helps save valuable natural resources

and prevents potential negative effects on the environment and human health, which

could result from improper waste disposal. Ask your local authorities or collection

facility for more details.

In accordance with national regulations penalties may be imposed for the incorrect

disposal of this type of waste.

For business entities in European Union states

If you want to dispose of electric or electronic devices, ask your retailer or supplier for

the necessary information.

Disposal in other countries outside the European Union.

This symbol is valid in the European Union. If you wish to dispose of this product,

request the necessary information about the correct disposal method from the local

council or from your retailer.

This product meets all the basic requirements of EU directives related to

it.

Sencor SCP 3701 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info