- 8 - 05/2020
Copyright © 2020, F
The SLEEP mode is a combination of the NA
agradual lowering of the fan speed.
Fan setting Progression of the SLEEP mode
High speed The applianc
NA
After 30 minutes, the high fan speed switches to
medium speed. After an additional 30 minutes,
it will switch to the low fan speed setting.
appliance will remain in the NA
the low fan speed set.
Medium speed The appliance will run for 30 minutes in the
NA
After 30 minutes, the medium fan speed switches
to low speed.
NA
Low speed The appliance will run in the NA
the low fan speed set.
Wa
This function serves exclusively for the purpose of drying out the water filter A10 .
If you intend to store and not use the appliance f
necessary to carefully dry out the water filter A10 and other parts to protect them
again the formation of mould.
Hold down button B2 for appro
fan speed automatically changes to high speed and will run for 20 minutes. During
this time, it is not possible to change the settings of the appliance. Only button
B1 will remain functional. After 20 minutes have elapsed, the applianc
automatically switch to the stand-by mode.
Note:
If the appliance is turned off with button B1 during the dr
process, and then is turned on again, the appliance will start at the setting
that was set prior to the dryer function being set.
Setting automatic vertical flap motion
Button B6 serves to turn the automatic v
light B11 is lit to indicaB6 again to stop
the vertical motion of the flaps.
Setting the angle of the horizontal flaps
The angle of the horizontal flaps A2 can be set manually by tilting them up or down.
When handling them, be careful not to damage them.
Automatic shut-off function
The appliance is equipped with an automatic shut-off function after 15 hours of
non-stop operation.
control button is pressed, the applianc
If you wish to cancel this function, hold down button B6 for appro
3 seconds.
cancelled. If you wish to activate this function again, hold down button B6 for
approximately 3 seconds
activated.
Pow
The display will dim out after 1 minute of inactivity.
button will turn the display on again.
REMOTE C
The function of the buttons on the remote control A15 and the contrA2 are
the same. If you wish to use the remote contrA15 , point it at the level of the signal
receiver A1 on the control panel A2 .
from the remote control A15 is 6 m.
Note:
If there are obstacles located between the remote conA15 and the
appliance, the signal may not be transmitted
FILLING THE W
Before filling the water tank A12 , turn the appliance off
power socket and secure the appliance against moving
Release the lock A13 by turning it to the horizontal position – see figure E1 .
TA12 and fill it with clean cold water – see figure E2 .
Insert the water tank A12 back into the appliance and turn the lock A13 to the
vertical position to secure the water tank A12 inside the appliance.
Always fill the appliance with clean cold wat
micro-organisms or moulds from multiplying, do not leave water in it f
aday
Warning:
When filling the appliance, make sure that the wa
at least the minimum water level mark and also that it does no go
past the maximum mark.
Note:
When the appliance is used for the first time, you ma
odour or discolouration of the water in the watA12 . This
a
effects on your health.
USING
The cooling inserts A16 enable the temperature of the water in the water tank t
reduced, which results in cooler air and fast
Insert the cooling inserA16 into afreezer for at least 12 hours.
into the part of the water tank A12 that is marked with acooling insert symbol. Fill
the water tank A12 with water and insert the cooling insert A12 into the body of
the appliance.
The appliance is supplied with two cooling inserts A16 , which ensures continuous
operation.
Warning:
It is forbidden to open the lock of the cooling insert A16 or to
damage its external case in any way
insert A16 is damaging to health. In the event of swallowing,
immediately seek medical help.
CLEANING AND MAINTENANCE
Disconnect the power plug from the power socket bef
For cleaning, do not use cleaning pr
could damage the appliance.
Warning:
T
the appliance, power cor
liquid.
CLEANING THE W
When you have finished using the watA12 , empty it out and rinse it with
clean water
T
or moulds from multiplying inside the water tank A12 , clean it out at least once
per month using acloth dampened in lukewarm water with the addition of neutral
detergent.
cloth.
CLEANING
Dirt and soils may accumulate on the dust filter A9 and water filter A10 during use,
which may negatively affect the operation of the appliance
these filters are regularly cleaned at least 1x per month.
the appliance is cleaned depends on its use. If it becomes excessiv
effectiveness of the appliance may be reduced
1.
2. Press the safety clip at the top of the dust filter A9 and tilt it out of the appliance
together with the water filter A10 – see figure F1 .
3. F2 .
4. A10 out of the dust filter A9 .
5. A9 with asoft sponge lightly dipped in warm water with asmall
amount of neutral cleaning agent.
6. Soak the water filter A10 in warm water with a
agent.
A9.
7.
instructions in section "Water filter dryer function").
CLEANING
T
addition of neutral detergent.
Storage
When not using the appliance for an extended period of time, disconnect the power
plug from the power socket and clean it accor
"Cleaning and maintenance"
Before storing it, check that the appliance and all its accessories ar
clean and dry.
Remove the battery from the remote control A14 .
Store the appliance in a dry
extreme temperatures and out of children'sr
