Bedienungsanleitung Sencor SMR 130 (Seite 2 von 3) (Englisch)

757129

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Important:

··

In order for other people to receive your transmission, they must

also be on the same channel that you are currently using. Refer

to the "Changing Channel" section for more information.

··

·When the PTT and/or CALL buttons are continuously pressed,

your PMR cannot receive any transmissions.

3.5 Roger Beep

The Roger Beep is a tone which is automatically transmitted

whenever the PTT button is released. This alerts the

receiving party that you have ended the transmission, and

you are now in receive mode.

3.6 Changing Channels

The PMR has 8 available channels. To change channels, in

normal mode;

a. Press the (Menu) button, the channel icon “1 ” on the LCD

screen will start blinking.

b. While the Channel icon is blinking, press the or

button to select the desired channel. The

channel changes from 1 to 8, or vice versa.

c. Press the (Menu) button to confirm your setting and return

to the standby mode.

Note:

Refer to the :Channel Table” section of this Owner’s Manual for

detailed frequency listing.

Battery meter

The battery icon is located in the left corner of the LCD panel. This battery icon

will displayed when low battery status. These indicate that the battery level

reaches its minimum level, at this stage the handset will emit two beep tones and

then it will automatically turn Off the power.

Battery life

The PMR has a built in power saver feature to make the batteries

last longer. But when you are not using the handset, it's better to

switch off to save the battery power.

3. Operation

3.1 Turning the Unit ON/OFF

To Turn ON;

a. Press and hold the (Power) button. A special “beep" sound

will be heard. The LCD screen will display the current channel.

To switch OFF;

b. Press and hold the (Power) button. A special “beep" sound

will be heard and the LCD screen will turn blank.

3.2 Adjusting the speaker volume

There are 8 volume levels, the current speaker volume level

is displayed on the LCD screen.

To adjust the speaker volume level, press the (UP) button to

increase, or press (DOWN) button to decrease. The LCD screen

will display the speaker volume icon bars ascending, or descending

respectively.

3.3 Receiving a Call

The unit is continuously in receive mode when the unit is turned

ON and not transmitting. When a signal is received on the current channel, 3.7 Calling (Paging) Tone

the receive signal icon“RX” will be displayed on the LCD screen. You can use the CALL button to send a tone to other users on

the same channel. To activate this feature;

3.4 Transmitting (sending) a. With the PMR in normal mode, press and release the

button. The unit will transmit a 2-second page tone to the other

a. Press and hold the PTT (Push to Talk) button to transmit your voice. unit/s set with the same channel within transmitting range.

The transmit signal icon “TX” will display on the LCD screen.

b. Hold the unit in a vertical position with the Mic (Microphone) 5 cm

away from the mouth. While holding the PTT button, speak into the

microphone in a normal tone of voice.

c. Release the PTT button when you have finished transmitting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SMR 130 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info