Bedienungsanleitung Sencor SMR 130 (Seite 3 von 3) (Englisch)

757129

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

3.8 Channel Scan 5.2 Low Battery Meter Indicator

Your radio can scan the 8 channels to any activity. This allows to find The PMR can detect the low battery level when battery

other radios without having to change the channel. voltage goes low. The battery icon will display the low

To activate this feature: battery status as follows.

a. Press and old the and button at the same time and channel When battery voltage at low battery level. The empty battery

symbol will appear at this stage and continue to blink

scanning will start immediately, with SC displayed on the The battery icon will continue to blink until it totally drain

screen and the channel number cycling through the channels. the battery voltage.

When a signal is detected, the unit will pause on that channel, while

receiving the signal and for a further 3 seconds. Note: To have good communication, once the battery reach

in low battery level, replace the batteries into new ones.

b. Press the PTT button to stop scanning and talk on that channel,

or press the or button to manually start the scanning.

c. To stop the scanning, press the button and return to 5.3 Microphone/Earphone/Charger Jack

standby mode. The SMR 130 is equipped with and auxiliary microphone, earphone,

and charge jack located at the opposite side of PTT button.

3.9 Monitor Feature Note: It requires a microphone/earphone with a 2.5mm, 3-pole

You can use the Monitor feature to check for weaker signals in the jack connector and this is not supplied with your SMR 130.

current channel.

a. Press and hold the and button at the same time. The 5.4 Using a Hands free kit (Headset)

receiving icons “RX” appears on the display. You can plug a hands free kit into the

Your handset will pick up any signals on the current channel. right side of your FX-238 handset. With

b. Press the button to stop the monitoring hands free kit, by pressing the PTT button

4.0 To Lock the Buttons to transmit and talk with other radios

With the buttons lock you can still transmit (TX), or call the current

channel, but you can not change the volume. To activate this 5.4 Specifications

feature;

In the standby mode, press and hold the until the

icon appears on the LCD screen.

To unlock the buttons

Press and hold again the button until the icon

disappears on the LCD screen.

Channel Frequency Table

5. Auxiliary Features

5.1 Power Saving

Your PMR unit has special circuitry designed to extend the life of

your battery. When the unit is not used for 4 seconds, it will

automatically switch into a low power mode. The Power

feature does not affect the PMR ability to receive

transmissions. When a signal is detected, it automatically

returns to full power mode.

Cha

nnels Avail

ble

8 Channels

Output Power (TX)

0.5 W

Range

Up to

Km.

Cha

nel

Frequency (MHz)

Cha

nel

Frequency (MHz)

446.00625

446.05625

446.01875

446.06875

446.03125

446.08125

446.04375

446.09375

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SMR 130 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info