759893

Sencor SSI 0710 Seite 7

7
Zoom out
Zoom in
Vorherige Seite
1/7
Nächste Seite
- 7 - 11/2019
Copyright © 2019, Fast ČR, a.s.
LIMESCALE PROTECTION SYSTEM
■ This steam station is equipped with an Anti-Calc system, which limits the formation
of limescale deposits inside the steam station and the iron. It is also equipped with
an automatic sensor, which informs you about the need to replace the limescale
filter When the filter is clogged, indicator C7 will be lit. If this happens, proceed
according to the instructions in chapter Replacement of the limescale and dirt filter.
TURNING OFF
■ When you have finished using it, set the temperature dial D2 on the iron A10 to MIN
and place the iron on the rest surface A5. Disconnect the power cord of the steam
station from the power socket and wrap it, together with the steam hose, around
the stand A2. Secure the power cord and hose in place using holder A6. Allow the
soleplate D3 and the rest surface A5 to cool down. After the iron has cooled down,
clean it according to the instructions in chapter Cleaning and maintenance.
TIPS FOR QUALITY IRONING
■ Do not fill the washing machine drum with too much laundry, otherwise it will be
overly crumpled up. You can also avoid overly crumpled laundry by setting alower
spin drying speed.
■ If you are ironing fabrics from blended materials (e.g. 40 % wool and 60 % synthetic
material), set the temperature according to the material which is ironed at alower
temperature.
■ If you do not know the composition of the fabric, identify the suitable temperature
setting by ironing apiece of the fabric from the underside. Start by setting a low
temperature and gradually increase it until the ideal temperatures is achieved.
■ Never iron over places that have sweat marks or other stains. The high temperature
fixes the stain in place, making it difficult to remove.
■ To avoid silk, wool and synthetic fabrics from being shiny after ironing, iron them
from the underside.
■ Some materials are easier to iron when they are lightly damp.
■ Spray fine fabrics before ironing them or iron them under alightly dampened wiping cloth.
CLEANING AND MAINTENANCE
CLEANING AFTER EVERY USE
■ Before cleaning, turn off the iron according to the instructions in chapter Using
the steam station. The steam station must be disconnected from the power socket
and cooled down. Slide the water tank A3 out of the steam station, empty out any
remaining water into the sink and insert the water tank A3 back into the steam
station.
■ In the event that the soleplate D3, the surface of the steam station A1 or the surface
of the iron A10 is dirty, wipe these surfaces with alightly dampened cloth and then
wipe dry.
■ For cleaning, do not use steel wool, solvents or cleaning products with an abrasive
effect, etc. to prevent damaging the surface being cleaned. When cleaning, never
submerge the steam station or iron in water.
REMOVING LIMESCALE DEPOSITS
■ Despite the fact that the steam station automatically identifies the need to remove
deposits, which is shown by indicator C7, we recommend that you clean the iron at
least once per month.
■ Make sure that the steam station is turned off using the On/Off button C1 and that it
is disconnected from the power socket. Pour approximately 1 litre of clean water into
the water tank A3. Connect the steam station to apower socket, set the temperature
dial D2 on the iron to MIN and wait until indicator D5 turns off.
■ Hold the iron in ahorizontal position above the sink and press button D4 and hold
it down for approximately 1 minute to pump the water from the steam station into
the iron. Once steam and hot water starts coming out of the soleplate D3, set the
temperature dial D2 to the highest temperature level. Then repeatedly press button
D4 and tilt the iron slightly from side to side several times until the water tank A3
is completely empty. Together with the released steam and water, also limescale
deposits from the inner parts of the soleplate D3 will be removed. You may repeat
this process once more if necessary.
■ Use button C1 to turn off the steam station, disconnect it from the power socket and
allow it to cool down. In the event that the soleplate D3 or the surface of the iron is
dirty, wipe with alightly dampened cloth and then wipe dry.
REPLACEMENT OF THE LIMESCALE AND DIRT FILTER
■ Check that the steam station is turned off using the C1. Take the water tank A3 our
of the steam station and slide the cassette with filter B3 out of it. Using asuitable
implement, e.g. asmall flat screwdriver, clip open the plug B5 from the underside
of the cassette B3 and take out the filter. Depending on the condition of the filter,
either clean it out thoroughly or replace it with anew one. Click the plug B5 back in
and insert the cassette B3 into the water tank A3. Insert the water tank A3 into the
steam station A1. Turn on the steam station using the On/Off button C1 and press
button C3 to reset the limescale protection system.
STORAGE
When you have finished ironing, pour out any unused water from the water tank A3
(careful, it may be hot), or allow it to evaporate and place the iron on the rest surface
A5 to cool down. Turn off the steam station using the On/Off button C1. Wind the
power cord and the steam hose around the stand A2 and secure them in place using
holder A6. Put the steam station in asuitable location so that it cannot be tipped over.
TECHNICAL SPECIFICATIONS
Rated voltage .................................................................................................................................. 230 V
Rated frequency........................................................................................................................50/60 Hz
Rated power input ..................................................................................................................... 2 500W
Steam output ..........................................................................................................................100 g/min
Water pressure ................................................................................................................................. 3 bar
Length of the power cord ..............................................................................................................3 m
Weight (without water) ............................................................................................... approx. 1.3 kg
Changes to text and technical parameters are reserved.
INSTRUCTIONS AND INFORMATION REGARDING THE
DISPOSAL OF USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC
EQUIPMENT
This symbol on products or original documents means that used
electric or electronic products must not be added to ordinary
municipal waste. For proper disposal, renewal and recycling hand over
these appliances to determined collection points. Alternatively, in
some European Union states or other European countries you may
return your appliances to the local retailer when buying an equivalent
new appliance. Correct disposal of this product helps save valuable
natural resources and prevents potential negative effects on the
environment and human health, which could result from improper
waste disposal. Ask your local authorities or collection facility for more details. In
accordance with national regulations penalties may be imposed for the incorrect
disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electric or electronic appliances, ask your retailer or supplier
for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this product,
request the necessary information about the correct disposal method from the local
council or from your retailer.
This product meets all the basic requirements of EU directives related
to it.
7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sencor SSI 0710 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info