Bedienungsanleitung Sencor SSI 5421 (Seite 7 von 10) (Englisch)

759886

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Steam Iron

SSI 5420RD / SSI 5421TQ

EN-7

2015 06/2015

Note:

During ﬁrst use, a weak cracking sound caused by the expanding plastic may be heard. This is an

entirely normal event, which will disappear in a short time.

While ironing, the indicator light A2 will intermittently turn on and off. This indicates that the

set temperature is being maintained.

First iron the laundry that requires the lowest temperature. This will save you time because the

soleplate Aqs heats up faster than it cools down.

If you are ironing at a high temperature and then set a lower temperature, wait until the soleplate

cools down.

3. CONTINUOUS STEAM FUNCTION

3.1 Set or turn off the continuous steam output using the continuous steam lever A5.

3.2 If you wish to iron with steam, the water tank Aqa must be ﬁlled with water and the temperature

dial A9 must be set in the range from ●●● to MAX, which is suitable only for certain types of textile

materials, see chapter Preparation before ironing. Use the continuous steam lever A5 to select

weaker ● or stronger ●● steam output.

3.3 If the continuous steam function is set at the same time as the temperature dial A9 is set to low ●

or medium temperature ●●, then water may drip from the soleplate Aqs. For this reason, the iron

is equipped with the Drip-Stop system, which automatically stops the steam process when the

temperature dial A9 is not set to a high enough temperature and so prevents potential dripping

from the steam outlets.

Note:

The iron continuously emits steam only if you hold it in a horizontal position. You can stop the

release of steam by standing the iron upright.

3.4 If you wish to iron without the continuous steam function, set the lever A5 to the position marked

by the symbol .

Attention:

Do not use the steam function for silk and synthetics so as not to damage the surface of the fabric.

4. STEAM BOOST FUNCTION

4.1 Press the steam boost button A3 to generate a strong ﬂow of steam which can even out even very

crumpled up textiles.

4.2 Only use the steam boost function when the temperature dial A9 is set in the range ●●● to MAX.

In order to use this function, the water tank Aqa must be ﬁlled with water. If the indicator light A2

is lit, wait until it turns off and only then press the steam boost button A3. Wait at least 5 seconds

before pressing the button A3 again.

4.3 The steam boost function can also be used when vertical ironing textiles (e.g. curtains, garments

hanging on coat hangers, etc.).

Attention:

Do not use the steam boost function for silk and synthetics so as not to damage the surface of

the fabric.

5. WATER SPRAY FUNCTION

• The water spray function can be used at any ironing temperature. Make sure that there is water in

the water tank Aqa and to spray textiles using the spray nozzle A7 press the spray button A4.

Note:

We do not recommend using the spraying function on silk and synthetics.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sencor SSI 5421 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info