Bedienungsanleitung Severin HV 7186 (Seite 17 von 104) (Alle Sprachen)

794445

Zoom out

Zoom in

Vorherige Seite

1/104

Nächste Seite

142 x 208 mm

For appliances with dust bags

Changing the dust bag

∙The dust bag can only hold a limited amount of dirt.

∙Therefore, make sure you change the dust bag if the suction power drops noticeably or the dust level indicator lights up

red:

1. Make sure that the appliance is switched off.

2. Remove the tool and the suction tube.

3. Press the button on the top of the appliance and remove the dust container by pulling it downwards.

4. Remove the cover from the dust container (see Fig. IV).

5. Remove the lled dust bag by pulling it upwards and dispose of it properly.

6. Insert a new dust bag following the direction of the arrow.

7. Replace the cover on the dust container and push it until you hear it click into place.

Attention! The dust container has a safety function that prevents incorrect insertion of the dust bag. If you cannot

mount the dust container back on the appliance, check that the dust bag has been inserted correctly.

8. Push the dust container back into the appliance until you hear it click into place.

Cleaning the HEPA lter

∙The HEPA lter can get clogged due to soiling, causing the suction power to drop. Make sure you clean the lter on a

regular basis.

At the latest

∙if the suction power seems to be reduced

∙before storing the appliance for an extended period

∙before sending the appliance to the service centre.

∙Cleaning the lter:

1. Make sure that the appliance is switched off and is not charging.

2. Remove the tool and the suction tube.

3. Remove the HEPA lter cover underneath the handle by turning it counter-clockwise.

4. Pull out the lter.

5. Tap the lter out. If necessary, brush off with a small brush and tap out any loose dust.

6. Slide the lter back in.

7. Replace the cover and lock in place by turning clockwise.

Changing the HEPA lter

When normally used for household purposes, the lter should be replaced every 6 months.

Cleaning the brush roller in the oor tool and the upholstery tool

Soiling may prevent the brush roller from rotating freely. Clean the brush roller regularly.

1. Make sure that the appliance is switched off and is not on charge.

2. Remove the tool from the suction tube.

Floor tool:

3. Press the button on the side of the tool ( ). You can pull the brush roller out of the housing from the side.

4. Remove any hair and dirt from the brush, using a pair of tweezers or scissors carefully, if necessary.

Attention! Carefully use scissors within the brush roller groove to cut away any hair or debris wrapped around the

brush roller.

5. Slide the brush roller back into the tool. To do this, press the red button and slide the brush roller back in from the side

until you hear it click into place.

Upholstery tool:

3. Loosen the locking latch on the side of the tool by turning it counter-clockwise.

4. Remove the brush roller.

5. Remove any hair and dirt from the brush, using a pair of tweezers or scissors carefully, if necessary.

6. Slide the brush roller back into the tool, push it down and lock in place by turning clockwise until the lock engages

above the elevation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin HV 7186 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info