Bedienungsanleitung Severin KS 9811 (Seite 17 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch, Finnisch)

603088

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Operating noise

∙ Certain typical sounds can be heard when the appliance is

switched on. These sounds are:

∙ caused by the electrical

motor within the

compressor assembly;

during compressor

start-up the sound level

will be slightly higher for

a limited period of time.

∙ caused by the cooling

agent ﬂ owing through the circuit.

Trouble-shooting

The following table lists possible malfunctions and their

probable causes and solutions. In the event of operational

p roblems, check ﬁ rst whether a solution can be found using this

table. If the problem persists, disconnect the appliance from the

mains power and contact our Customer Service Department.

Problem Possible cause and solution

The appliance is not working at all. ∙ The temperature control is set to ‘0’.  Use a higher temperature setting.

∙ The wall socket is defective.  Check the fuse. If necessary, have the wall outlet

checked by a qualiﬁ ed electrician.

The inside temperature is not low

enough.

∙ Too much food has been stored in the appliance.  Do not store excessive food (see

product data sheet).

∙ The doors are not properly closed.  Ensure that the doors are properly closed.

∙ The door seals are defective.  Check the door seals and contact our Customer

Service if necessary.

∙ There is too much dust on the condenser.  Clean the condenser regularly.

∙ Insufﬁ cient ventilation: the unit is too close to a wall or other structure or object. 

see section ‘Ventilation’.

∙ The temperature control is set too low.  Use a higher setting.

The normal operating sound changes

or becomes louder.

∙ The unit is not ﬁ rmly set on the ﬂ oor.  Use the adjustable front feet to align the unit

properly.

∙ Adjacent furniture or objects are affected by the running of the cooling unit (i.e. causing

them to vibrate).  Keep the stated clearances.

∙ Any objects on top of the unit might be vibrating  Remove such objects.

Excessive build-up of frost inside the

freezer compartment.

∙ It is necessary to de-frost the freezer compartment manually.  See ‘De-frosting and

cleaning’

Reversible door

∙ If required, the door may be reversed, i.e. from right-hinged

(default installation) to left.

∙ To avoid the risk of personal injury or damage to the unit,

two people are needed to reverse the door.

∙ Warning: Always disconnect the unit from the mains before

any maintenance or repair work is carried out.

∙ Before you start, please note the following:

∙ Always ensure that the correct number of washers is used

on all hinge bolts and screws.

∙ So that the doors can close tightly against the frame, take

the utmost care that they are properly aligned during re-

assembly.

Diagram similar!

1. Open the freezer door.

2. Remove the four covers C from the housing and inside of

the door.

3. Replace the extension of the 2-part cover, turned through

180, on the opposite side.

4. Unscrew the hinge bolt on the inside of the door in the

area C/6. Caution: Support the door.

5. Take off the freezer door and place it on a soft surface.

Remove the hinge support from the underside of the door

and ﬁ t the hinge support provided on the opposite side.

6. Take out the ﬁ xing screws and remove the upper bracket

6. Note the small plastic plate underneath the bracket.

7. Turn the bracket 6 including the small plastic plate through

180° and replace it on the other side of the cabinet

freezer, using the two screw holes adjacent to each other.

8. Remove the lower panel 1 by lifting it up slightly.

9. Take out the ﬁ xing screws and remove the bracket 2 with

its hinge bolt.

10. Unscrew the hinge bolt, together with the serrated lock

washers, from the bracket, and ﬁ t it into the corresponding

opening on the opposite side of the bracket.

11. Remove the bracket 7 and replace it with the holding

bracket 2 with its hinge bolt.

12. Now install the holding bracket 7 in the previous position

of the bracket 2.

13. Place the freezer door onto the hinge bolt on holding

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Severin KS 9811 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info