663263

Shada 1000451 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/10
Nächste Seite
MV#: 20160920 08:45
Art. Nr.:1000451
Installation and Operating Manual
Before You Begin
Carefully unpack contents and check to make sure all parts are present. Some assembly may
be required.
Assembly
1. Remove battery cover from remote and install 23A battery (included). (Fig.3)
• Please note the correct position of the battery
• Please note that the remote control is for indoor-use only and is not weatherproof.
2. Attach light to stake.
To attach stake (Fig.1)
a. Remove the hex screw and washer from the stake with the included tool.
b. Use the same hex screw and washer to attach the stake to the pivot bracket.
c. Stake to ground.
3. Position the projector by loosening and tightening the angle adjustment screws (Fig. 1). A
distance of 3-5m from the wall will yield about 64m.
4. Attach projector to transformer by fully inserting the two-pronged plug and tighten the
wire cap (Fig.2).
5. Plug unit into a 220VAC/60Hz power outlet (Caution: The Outdoor Laser will turn on once
it is plugged in. Up to 30 minutes warm-up
time may be necessary for conditions below -25°C. Following precautions for laser usage on
page 3, re-aim if necessary).
Remote control Pairing
The coding of the remote controller will need to be paired
to the unit.
Please note that sometimes electrical interference from the
power line may disrupt the coding and you may need to pair
the unit again if the unit becomes uncontrollable
To pair the unit, just plug in the unit and press the On/O
button on the Remote Controller within 5 seconds. Your
Outdoor Laser will turn o. Your Remote is now paired.
Operation
1. Power ON/OFF (i) - The Outdoor Laser will default to turnon when plugged in. Pressing
the power button will turn the lights OFF and will be in standby mode. Timer, color or
flash settings are retained in standby mode until the device is unplugged. To turn the
lights back on, simply press the power button.
2. Color select - Your Outdoor Laser come’s loaded with fun features. You can use below to
guide yourself through these amazing features.
Light: The default setting is both Red and Green Lasers on simultaneously. Press (j) once
to turn on just the Red Laser. Press again to turn on just the Green Laser. Pressing again
will take you back to both the Red and Green Lasers on simultaneously
3. Flash mode (k) - Pressing this button will cycle between steady or flashing lights. For
multi-color versions, it will cycle from simultaneous flashing, alternation flashing, single
color flashing back to default.
• Simultaneous flashing - Both laser colors (if applicable) will flash simultaneously.
• Alternating flashing - Both laser colors will alternately flash (multi-color only). Press
again and it will default back to simultaneours color (no flashing).
4. Timer presets (2, 4 or 6 hours) (m) - Pressing this will turn the unit ON and go into stand-
by Mode after #hours.For example, if you want your Outdoor Laser to display from 6pm
to midnight daily: At desired time, in this case, 6pm, press the “6h” button. The lights
will turn o after 6hrs (midnight) and will cycle again to turn on at 6pm the next day
and so on. Timer settings will be saved until “On/O” button is pushed or if the projector
unit is unplugged. A triple-flash indication from the projector will confirm your timer
setting.
5. LED indicator on remote (h) - This will confirm the remote battery / buttons are working.
6. Speed Control (l) - you can control the speed that your Outdoor Laser lights move at. You
can even freeze them. There are 3 levels of speed, Slow, Fast and Faster. Pressing the “S+”
button will increase the speed to the next level. Pressing the “S-” button will decrease
the speed to the next level, the last level being stopped. Pressing the “S+” button once it
has reached the fastest speed will have no further eect. Pressing the “S-” button once
the lights has stopped will have no further eect. Press the “S+” button to get the lights
moving once again.
7. Retractable Antenna (g) - Extend for maximum range (Up to 10m. depending on surroun-
dings). However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the manufacturer or an experienced radio/TV technician for help. NOTE: This
is a standard cautionary statement from the FCC, which is used to alert the user to
troubleshoot in various ways if problems are found.Read All Instructions
WARNING: When using outdoor use portable luminaires, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and personal injury, including
the following:
a) Use only three-wire outdoor extension cords that have three-prong grounding plugs and
grounding receptacles that accept the appliance’s plug.
b) Ground Fail Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or
outlet(s) to be used for the wet location portable luminaire. Receptacles are available
having built-in GFCI protection and are able to be used for this measure of safety.
c) Use only with an extension cord for outdoor use.
IMPORTANT SAFETY INSTRUCTIONS
This product has a polarized plug (one blade is
Wider than the other) as a feature to reduce the
Risk of electric shock. This plug will fit in the outlet.
Never use with an extension cord unless plug can be fully inserted. Do not alter the plug.
The Outdoor Laser is generally safe when used responsibly, please exercise the following
precautions:
• Do not aim or shine at people, animals or trac from land, sea, or air.
• Use with caution within 9-15km of an airport.
• The Outdoor Laser should always be stationary, do not hold in hand when operating.
• Position The Outdoor Laser so that the lights are within the confines of the target object.
box contents:
(A) 1 x double beam laser projector
(B) 1 x Radio Remote Control unit
(C) 1 x Groundstake with attachment screw
(D) 1 x Power Supply transformer
(E) 1 x Allen key
(F) 1 x Operating and safety manual
Product specifictions:
2x Class II laser both <1mW
green 532nm - Red 660 nm
lifetime of laser diodes: ≈7.000h at max. 4 hours a day
power consumption: 5W
Power input: 230V AC (when used with manufacturer provided transformer)
operating temperature (T in °C): -25≤T≤33
Projection coverage: 64 m
Notes on Disposal
Old units, marked with the symbol as illustrated,
may not be disposed of in the household rubbish.
You must take them to a collection point for old
units (enquire at your local authority) or the de-
aler from whom you bought them. These agencies will ensure
environmentally friendly disposal.
Care and warranty
Before cleaning the unit, disconnect it if necessary from other
components; do not use aggressive cleaning agents.
The unit has been carefully checked for defects. If nevertheless
you do have cause for complaint, please go back to the retailer
where you have bought the product together with your proof
of purchase. We oer a 2year warranty from date of purchase.
We are not liable for damage arising from incorrect handling,
improper use or wear and tear. We reserve the right to make
technical modifications.
Visit us online at www.shada.nl for more information about
our products and our company.
CE declaration
This product complies with the following directives:
LVD 2014/35/EU
EMC 2014/30/EU
RoHS 2011/65/EU
Additionally, for Products with Radio transmitter units:
R&TTE 2014/53/EU
The complete Declaration of Conformity Document (DOC) can
be found here:
http://www.shada.nl/uploads/DoCs/index.html
WEEE NL: 3505
WEEE DE: 37281017
WEEE AT: 40133
Imported by
Kanaal Noord 350
NL-7323 AM Apeldoorn
www.shada.nl
LED’s
light
A
BRAND
SHADA
LED’s
light
A
BRAND
SHADA
2 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Shada 1000451 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info