Bedienungsanleitung Shark SV800 (Seite 4 von 13) (Englisch, Französisch, Spanisch)

668682

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

OPERATING INSTRUCTIONS

Cleaning the Filter

It is recommended that the filter be

cleaned every full discharge of the

battery. To remove the foam filter:

1. Remove the dust cup from the

vacuum.

2. Pull out the filter fame with the foam

filter from the top. (Fig. 12)

3. Remove the foam filter and wash in

lukewarm water and let it air dry

completely before replacing it into the

vacuum. Never use a hair dryer or

any other hot forced air to dry the

foam filter.

4. When the foam filter is completely

dry, reinsert it into the filter frame and

replace it into the filter compartment.

NOTE: The foam filter must be replaced

every three months to maintain best

performance of the vacuum.

Changing the Belt

Occasionally the motorized brush drive

belt will require changing, the frequency

will depend upon the amount of use your

stick vac sees. To change the belt:

1. Remove the motorized brush from

the vacuum.

2. Turn the motorized brush upside

down and using a screw driver,

remove the screw at the rear of the

access cover. (Fig. 13)

Fig. 13

3. Put the screw to the side and lift the

access cover to remove it. (Fig. 13)

4. Lift the end of the brush bar and

remove the end cap. (Fig. 14)

5. Remove any pieces of the belt.

6. Slide one end of the new belt around

the drive shaft and the other around

the brush roll. (Fig. 14)

7. Place the end cap on the end of the

brush roll

8. Align the end cap with the slot in the

motorized brush head and slide it

down carefully.

9. Snap the access cover in place and

replace the screw.

Drive

shaft

Belt

End

cap

Brush

roll

Fig. 14

Fig. 12

Filter

frame

Filter

compartment

Foam

filter

To Maximize the Life of your NiCd

Batteries

NOTE: If the product has never been

used or has been stored for an extended

period of time without use – it will take

several complete charge and discharge

cycles to realize the full operational time

of your product.

1. Charge the battery for 24 hours

before initial use. Failure to do so

will reduce the product’s battery life

significantly.

2. Only recharge when the battery is

fully discharged (or as close to fully

discharged as possible).

3. Do not store in areas of high

temperature or humidity.

4. Fully discharge, then completely

re-charge the unit at least once a

month.

5. After three (3) months of storage,

the product should be fully

discharged and then recharged to

maximize battery power.

OPERATING INSTRUCTIONS

Replacing the Battery

WARNING: NEVER use ordinary

batteries for replacement, as these may

leak and damage your vacuum cleaner.

Use only battery pack XBT800 provided

by EURO-PRO Operating LLC for

replacement.

Battery Pack Disposal

This stick vac is equipped with NiCd

batteries and you need to dispose of

them properly. When the battery pack is

no longer good for use, it must be

removed from the stick vac for disposal.

The battery pack must be recycled or

disposed of in accordance with local

regulations. Please consult your

Yellow Pages or local recycling

center for more information.

CAUTION

•

Use only with the battery pack

supplied with the unit.

• Never attempt to throw the battery

pack or unit into a fire or incinerate it.

• DO NOT attempt to remove or

damage the battery casing.

• Battery must be recycled or disposed

of properly at the end of it's service

life.

• DO NOT place batteries on metal

surfaces.

• DO NOT touch metal parts of the

batteries together as the batteries will

overheat.

Cleaning the Motorized Brush

CAUTION: Remove the battery pack

to avoid the unit turning on

accidentally.

Periodically remove the motorized

brush from the stick vac to remove any

build up of lint, hair or fiber on the

rotating brush.

1. Remove the battery from the

battery pack compartment.

2. Place the vacuum on a flat surface

upside down.

3. Carefully slide a pair of scissors

under any trapped threads, pet hair,

or carpet fibers.

4. Cut along the threads, hair or fibers

and then remove these from

around the bristle brush.

NOTE: If your motorized brush

becomes jammed, your stick vac will

cease to operate. If this occurs, turn

the unit “Off” and allow the unit to cool

down for 2 minutes. Ensure that there

are not any threads or fibers around

brush. Then turn the power “On” and

unit should now operate normally. Call

customer service at 1 (800) 798-7398 if

the vacuum needs any other servicing.

6. Use only the charging base and

charging adapter supplied with the

product. If other chargers are used,

the batteries can fail causing damage

to the battery, product or personal

property.

7. The charging indicator light on the

charging base will light up when the

battery is inserted to be charged. If

the charging indicator does not light,

check to make sure that the battery

was inserted properly. If it still does

not light up, then check the fuse or

the breaker.

8. NiCd batteries have a long useful life

but at some time they will need to be

replaced. To purchase replacement

batteries visit www.sharkvac.com.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Shark SV800 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info