Bedienungsanleitung Sharp ARM205 (Seite 48 von 96) (Englisch)

26406

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

USER SETTINGS

Memory allocated to

printer mode

1: 30%

2: 40%

3: 50%

4: 60%

5: 70%

• Use this to change the proportion of machine

memory used for printer mode.

Key auto repeat

0: OFF

1: ON

• Use this setting to select whether or not holding

down a key causes repeated input of the key.

For keys that normally cause a set value to

increase when held down (for example, holding

down the [ZOOM] key (

)), this program

can be used to have the set value not change

when the key is held down.

Key press time

1: Minimum

(current response speed)

2: 0.5 sec.

3: 1.0 sec.

4: 1.5 sec.

5: 2.0 sec.

• Use this setting to select how long a key must

be pressed for the input to be accepted. By

selecting a longer time, you can prevent

settings from being changed by the accidental

pressing of a key.

Audible signals volume

1: Low

(current volume)

2: High

3: OFF

• This sets the volume of beep signals. (p.47)

Base setting beep

signal

0: OFF

1: ON

• Use this to sound a beep when a base setting is

selected. (p.47)

Number of copies limit

1: 99 copies

2: 999 copies

• Use this setting to select 99 or 999 for the

maximum number of copies.

Use close paper size

0: OFF

1: ON

• When this function is enabled, printing in printer

mode will automatically continue using a

different size of paper if the specified size of

paper runs out in all trays. This feature does not

function in copy mode.

Default tray setting

1: Upper paper tray*

2: Lower paper tray*

3: 250-sheet paper feed

unit/

Upper paper tray of 2

x 250-sheet paper*

feed unit

4: Lower paper tray of 2

x 250-sheet paper

feed unit*

5: Bypass tray*

• Use this program to select a default tray. This

tray is automatically selected each time the

power is turned on or each time the machine

reverts to the initial settings.

Default exposure mode

1: AUTO

2: TEXT

3: PHOTO

• Use this program to set "AUTO", "TEXT", or

"PHOTO" as the default exposure mode.

USB 2.0 mode

switching

1: Full-Speed

2: Hi-Speed

This sets the USB 2.0 data transfer speed. To

obtain the fastest speed when using the USB 2.0

port, first verify that your computer meets the

system requirements (operating system and

driver), and then use this program to change the

USB 2.0 mode to "Hi-Speed". Note that the setting

should not be changed while running a TWAIN

driver. (For the system requirements, see "System

requirements for USB 2.0 (Hi-Speed mode)"

(p.38).)

Program

number

Program name

Setting codes

(factory default setting

appears in bold)

Explanation

AR-M160 is as follow:

1: Upper tray (factory default), 2: 250-sheet paper feed unit/Upper paper tray of 2 x 250-sheet paper feed unit,

3: Lower paper tray of 2 x 250-sheet paper feed unit, 4: Bypass tray

The scanning speed increases when the USB 2.0 mode is set to "Hi-Speed", however, the printing speed does not increase

considerably.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp ARM205 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp ARM205

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info