Bedienungsanleitung Sharp GX-BT60 (Seite 8 von 64) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

787660

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

connection. The GX-BT60 will prompt

“disconnected”. Then other Bluetooth

devices can  nd and pair with the

GX-BT60.

Duo Mode

Dual speaker wireless stereo pairing for

wide stereo sound stage.

1. Press the power button on the  rst

speaker to turn the speaker “On”

2. Press and hold the Volume + and

Volume - buttons on the  rst speaker

until the speaker says “Duo Mode

pairing” then release the buttons

3. Press the power button on the second

speaker to turn the speaker “On”

4. Press and hold the Volume + and

Volume - buttons on the second

speaker until the speaker says “Duo

Mode pairing” then release the buttons

5. Please wait until you hear the voice

prompt “Duo Mode connected”.

This may take up to 1 minute. The

speakers are now connected to each

other.

6. The  rst speaker in which Duo Mode

was initiated is the master speaker and

will be the right stereo channel. You

should pair your mobile device with

this speaker.

For Bluetooth pairingto a Bluetooth-out

enabled smart device search for “GX-BT60”

on your device and pair.

If you receive a phone call while in Duo

Mode the call will only come through the

master speaker.

When in Duo Mode and you Power oﬀ one

speaker both speakers will power oﬀ .

When you Power on the speakers, they

need to be turned on individually.

When both speakers are powered on Duo

Mode will automatically reconnect and

you will hear “Duo Mode connected”.

To disconnect Duo Mode press and hold

Volume + and Volume - until you hear “Duo

Mode disconnected”.

To clear Duo Mode pairing press and hold

Volume + and Volume - until the speaker

says “Duo Mode cleared”. This takes about

8 seconds.

Assuming direct line of sight, you should

achieve be able to achieve a range of over

40 metres between the two speakers.

When used indoors, the range will be

aﬀ ected by any internal walls or obstacles

between the speakers.

Aux in Mode

Use the 3.5mm audio cable (included) to

connect the speaker to an audio source

(PC, MP3/MP4, mobile phone).

When you plug the Aux cable into the

GX-BT60 it will automatically change to

Aux in mode. When you unplug the Aux

cable the GX-BT60 will change back to

Bluetooth mode.

The speaker will play the music from the

audio source.

► Click to mute play back

Click to decrease volume

Click to increase volume

To change or control tracks please use your

music source when in Aux in mode.

Model SHARP GX-BT60

Output Power 6W (RMS)@10% THD

Power Consumption 6W

Power consumption – Standby <1mW

Frequency Response 110Hz - 20kHz

Operating Temperature 5°C - 40°C

Battery Type Li-ion 3,7V / 1800mAh / 6,66Wh

Bluetooth

Version V 5.0

Frequency bands 2402 MHz ~ 2480 MHz

Maximum power transmitted <20dBm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp GX-BT60 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info