Bedienungsanleitung Sharp LC -42RD2EA (Seite 21 von 40) (Englisch)

559932

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Menu operations

HDMI Setup

HDMI (High-Definition Multimedia Interface) terminal

selection.

1 To watch an HDMI equipment image, select

“EXT5” or “EXT6” (the terminal which you are

using) from “INPUT SOURCE” menu using b

on the remote control unit or TV.

2 Press MENU and the MENU screen displays.

3 Press c/d to select “Option”.

4 Press a/b to select “HDMI Setup”, and then

press OK.

• “HDMI Setup” is displayed only when “EXT5” or

“EXT6” is selected from the INPUT SOURCE menu.

DNR (Digital Noise Reduction)

Menu Operation: A (page 12)

Produce a clearer image. (Off, High, Low)

Colour System

Menu Operation: A (page 12)

You can change the colour system to one that is

compatible with the image on the screen. (AUTO, PAL,

SECAM, NTSC3.58, NTSC4.43, PAL-60)

NOTE

• Factory preset value is “AUTO”.

• If “AUTO” is selected, colour system for each channel is

automatically set. If an image does not display clearly,

select another colour system (e.g. PAL, SECAM).

• “NTSC3.58”, “NTSC4.43” and “PAL-60” cannot be

selected in TV tuner mode.

Input Select

Menu Operation: A (page 12)

For setting the signal type of external equipment.

NOTE

• If no (colour) image displays, try to change the other

signal type.

• Check the operation manual of the external equipment

for the signal type.

• TV, EXT5 and EXT6 are not displayed in Input Select.

• If both CVBS and RGB signals are input to EXT 1 or EXT 2

using a SCART cable, the TV may output an RGB signal

even though you have designated CVBS for the respective

terminal. This happens due to the setting of your external

equipment.

• EXT 3 has “Rear” and “Side” terminals. Confirm which

terminal you have connected, and select the appropriate

terminal under “Input Select”. When using S-VIDEO, select

“Rear” for EXT3.

AV only

TV/AV only

TV/DTV/AV only

[

Option

...

HDMI Setup

]

Option

Audio Only

DNR

HDMI Setup

[Off]

5 Press a/b to select the desired item, and then

press OK.

6 Press a/b/c/d to select the desired setting, and

then press OK.

Selectable items

RGB/YCbCr 4:4:4/

YCbCr 4:2:2

ITU601/ITU709

Normal/

Enhanced

Disable/Enable

Digital/Analogue

HDMI Setup

items

Signal

Type*

Colour

Matrix*

Dynamic

Range*

Auto View

Audio

Select**

Description

Select the video signal

type from the HDMI

terminal.

Select the internal colour

space conversion method

when an RGB signal is

input.

Select the signal amplitude

range. Usually, select

“Normal”.

Set whether or not to use

WIDE MODE based on

signal recognition,

including an HDMI signal.

Select “Digital” for audio

signal via the HDMI

terminal. Select “Analogue”

for audio signal via the

AUDIO jack.

NOTE

• Refer to your external equipment operation manual for

the signal type.

• Items marked * may be greyed out (with 4) depending

on the type of signal input from the external equipment.

• Item marked ** is only available when EXT5 is selected.

Input source Signal type

EXT 1 Y/C, CVBS, RGB

EXT 2

Y/C, CVBS, RGB

EXT 4 PC (RGB), COMPONENT (Y, PB, PR)

EXT 3 CVBS, S-VIDEO

CVBS

Rear

Side

LC-42RD2EA_GB_b 07.6.20, 5:38 AM19

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp LC -42RD2EA Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp LC -42RD2EA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info