Bedienungsanleitung Sharp lc 26 sa1 (Seite 23 von 28) (Englisch)

141056

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

• Check if you pressed B on the remote control unit. (See page 7.)

If the indicator on the TV lights up red, press B.

• Is the AC cord disconnected? (See page 3.)

• Check if you pressed a on the TV. (See page 7.)

• External influences such as lightning, static electricity, etc., may cause improper

operation. In this case, operate the unit after first turning the power off, or

unplugging the AC cord and re-plugging it in after 1 or 2 minutes.

• Are batteries inserted with polarity (e, f) aligned? (See page 4.)

• Are batteries worn out? (Replace with new batteries.)

• Are you using it under strong or fluorescent lighting?

• Is a fluorescent light illuminated to remote control sensor?

• Is the image position correct? (See page 17.)

• Are screen mode adjustments (4:3 Mode/WSS) such as picture size made

correctly? (See pages 17 and 19.)

• Adjust the picture tone. (See pages 12 and 13.)

• Is the room too bright? The picture may look dark in a room that is too bright.

• Check the colour system setting. (See pages 15 and 18.)

• Check the HDMI Setup setting. (See page 18.)

• The unit’s internal temperature has increased.

Remove any objects blocking vent or clean.

• Check the power control setting. (See page 14.)

• Is sleep timer set? Press SLEEP on the remote control unit until it sets to Off.

• Is connection to other components correct? (See page 8 and 9.)

• Is input signal type selected correctly after connection? (See page 18.)

• Is the correct input source selected? (See page 8.)

• Is non-compatible signal being input? (See page 23.)

• Is picture adjustment correct? (See pages 12 and 13.)

• Is the antenna connected properly? (See page 3.)

• Is “On” selected in “Audio Only”? (See page 17.)

• Is the volume too low? (See pages 5 and 6.)

• Make sure that headphones are not connected. (See page 6.)

• Check if you pressed e on the remote control unit. (See page 5.)

Troubleshooting

Appendix

IMPORTANT NOTE ON RESETTING THE PIN

We suggest that you remove the following instruction from the operation manual to prevent children from

reading it. As this operation manual is multilingual, we also suggest the same with each language. Keep it in

a safe space for future reference.

Cautions regarding use in high and low temperature environments

• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly

delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.

• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near

a heater, as this may cause the cabinet to deform and the LCD panel to malfunction.

Storage temperature: –20°C to e60°C.

1 Repeat steps 1 to 3 in Changing the PIN. (See page 16.)

2 Enter “3001” to cancel out the current PIN.

• The PIN resets to the factory preset “1234”.

Problem Possible Solution

• No power.

• Unit cannot be operated.

• Remote control unit does not

operate.

• Picture is cut off.

• Strange colour, light colour, or

dark, or colour misalignment.

• Power is suddenly turned off.

• No picture.

• No sound.

LC-32SA1E_GB_c 06.7.25, 11:36 AM21

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp lc 26 sa1 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info