Bedienungsanleitung Sharp pg b10s (Seite 69 von 82) (Englisch)

214299

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

-65

Appendix

Lamp

■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be-

comes 5% or less, or when you notice a significant deterioration in the picture and color quality.

The lamp life (percentage) can be checked with the on-screen display. See page 41.

■ For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service

Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service

of this projector under warranty, including lamp replacement, must be obtained through a Sharp Autho-

rized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer

or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

U.S.A. ONLY

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp

failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface

scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure

largely varies depending on the individual lamp and/or the condition and the frequency of use. It is

important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended

that the lamp be replaced with a new one immediately, even if the lamp appears to be operating

normally.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the

lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes

mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In

case of exposure to the gas, consult a doctor as soon as possible.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the

projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector

Dealer or Service Center to remove the damaged lamp and assure safe operation.

Replacing the Lamp

Caution

• Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching

it can lead to burn or injury.

• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool

before removing the lamp unit.

■ If the new lamp does not light after replacement, take your projector to the nearest Sharp Autho-

rized Projector Dealer or Service Center for repair. Purchase a replacement lamp unit of type BQC-

PGB10S//1 from your nearest Sharp Authorized Projector Dealer or Service Center. Then carefully

change the lamp by following the instructions described in this section. If you wish, you may have

the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

Regarding the Lamp

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp pg b10s Seite 69

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp pg b10s

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info