Bedienungsanleitung Sharp PN-465 (Seite 11 von 184) (Deutsch, Englisch, Französisch)

64605

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

ENGLISH

How to Install the Monitor

Mounting precautions

• Since the monitor is heavy, consult your dealer before

installing, removing or moving the monitor.

• When installing, removing or moving the monitor, ensure

that this is carried out by at least 2 people.

• A stand and mounting bracket compliant with VESA

speciﬁcations is required. Do not use any screw holes other

than VESA holes for installation.

• When moving the monitor, be sure to hold it with the

handles both on the rear and the unit bottom. Do not hold

the LCD panel. This may cause product damage, failure, or

injury.

• Install the monitor with the surface perpendicular to a

level surface. If necessary, limit the tilt between 0 and 20

degrees downward.

• Mounting the monitor on the wall requires special expertise

and the work must be performed by an authorised SHARP

dealer. You should never attempt to perform any of this

work yourself. Our company will bear no responsibility

for accidents or injuries caused by improper mounting or

mishandling.

• This monitor should be used at an ambient temperature

between 0°C and 40°C. Provide enough space around the

monitor to prevent heat from accumulating inside.

For the monitor in horizontal orientation

Unit: cm

5 5

For the monitor in vertical orientation

Unit: cm

5 5

* The monitor can be installed close to a wall, etc.

However, the monitor emits heat during operation. Be

aware that heat emitted from the monitor may discolour

or alter the wall.

If it is difﬁcult to provide such space because the monitor is

installed inside a housing or for other reasons, take other

measures to keep the ambient temperature between

0°C and 40°C such as installing a fan in the housing.

• Adhere to the following when installing the monitor in the

vertical orientation. Failing to adhere to the following may

cause malfunctions.

- Install the monitor such that the power LED is located on

the downside.

- Set the MONITOR on the SETUP menu to PORTRAIT.

(See page 19.)

• Do not block any ventilation openings. If the temperature

inside the monitor rises, this could lead to a malfunction.

• After mounting, it is recommended to take some measures

to prevent the monitor from falling down.

• Do not place the monitor on a device which generates heat.

• Be sure to use a stand or a wall-mount/ceiling-mount

bracket designed or designated for mounting the monitor.

• This monitor is designed to be installed on a concrete wall/

ceiling or pillar. Reinforced work might be necessary for

some materials such as plaster / thin plastic board / wood

before starting installation.

This monitor and bracket must be installed on a wall which

can endure at least 4 times or more the weight of the

monitor. Install by the most suitable method for the material

and the structure.

• Use the supplied vertical logo sticker when you install the

monitor in vertical orientation.

INPUT

* Do not remove the factory-afﬁxed sticker but afﬁx the logo

sticker over it. Be careful not to cover the remote control

sensor or buttons.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp PN-465 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info