Bedienungsanleitung Sharp PN-465 (Seite 12 von 184) (Deutsch, Englisch, Französisch)

64605

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Connecting Peripheral Equipment

Caution

• Be sure to turn off the main power switch and disconnect

the plug from the power outlet before connecting/

disconnecting cables. Also, read the manual of the

equipment to be connected.

• Be careful not to mix up the input terminal with the output

terminal when connecting cables. Mixing up the input and

output terminals may cause malfunctions and the other

problems.

Connection with a PC

PC1 input terminal

PC audio input terminal

PC2 input terminal

PC3 input terminals

R G

• Use a commercially available signal cable (DVI-D 24

pin) for the PC1 input terminal. Set DVI SELECT on the

OPTION menu to PC (DIGITAL) when using the PC1 input

terminal. (See page 19.)

• Use a commercially available signal cable (Mini D-sub

15 pin) for the PC2 input terminal.

• Use a commercially available signal cable (BNC) for the

PC3 input terminals. Set BNC SELECT on the OPTION

menu to PC (ANALOG) when using the PC3 input

terminals. (See page 19.)

• Use a commercially available audio cable (mini stereo jack)

for the PC audio input terminal. Use an audio cable without

resistance.

TIPS

• Images may not be displayed properly depending on the

computer (graphics board) to be connected.

• A screen with 1920 x 1080 resolution may not be displayed

correctly on PC3 (BNC). In this case, check the settings of

your computer (graphics board) to verify that input signals

conform to speciﬁcations of this monitor (Hsync: 66.3 kHz,

Vsync: 60 Hz, and Dot frequency: 148.5 MHz). (See page

35.)

• If there is a check box to disable EDID in display control

panel, check it when using PC3 (BNC).

• Use the automatic screen adjustment when a PC screen is

displayed for the ﬁrst time using PC2 or PC3, or when the

setting of the PC is changed. (See page 23.)

• The screen is adjusted automatically when SELF ADJUST

in the OPTION menu is set to “ON”. (See page 19.)

Connection with AV equipment

AV1 input terminal

AV audio input terminals

AV2 input terminals

AV3 input terminal

Cr/Pr Y Cb/Pb

• Use a commercially available signal cable (DVI-D 24 pin)

for the AV1 input terminal. Set DVI SELECT on the OPTION

menu to AV (DIGITAL) when using the AV1 input terminal.

(See page 19.)

• Use a commercially available component cable (BNC) for

the AV2 input terminals. Set BNC SELECT on the OPTION

menu to AV (COMPONENT) when using the AV2 input

terminals. (See page 19.)

• Use a commercially available video cable (BNC) for the

AV3 input terminal.

• Use a commercially available audio cable (RCA) for the AV

audio input terminals.

• The AV1 input terminal is compatible with the video signals

below:

1920 x 1080 p @ 50/59.94/60 Hz

1920 x 1080 i @ 50/59.94/60 Hz

1280 x 720 p @ 50/59.94/60 Hz

720 x 576 p @ 50 Hz

720 x 480 p @ 59.94/60 Hz

640 x 480 p @ 59.94/60 Hz

• The AV2 input terminals are compatible with the video

signals below:

1080i (1125i)/50, 1080i (1125i)/60, 720p (750p)/50,

720p (750p)/60, 576p (625p), 576i (625i), 480p (525p),

480i (525i)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp PN-465 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info