Bedienungsanleitung Sharp R-622STM (Seite 18 von 20) (Englisch)

564581

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

GB-17

TROUBLESHOOTING

TROUBLESHOOTING CHART

QUERY ANSWER

Draught circulates around the door. When the oven is working, air circulates within the cavity.

The door does not form an airtight seal so air may escape from the door.

Condensation forms in the oven,

and may drip from the door.

The oven cavity will normally be colder than the food being cooked, and so steam produced when

cooking will condense on the colder surface. The amount of steam produced depends on the water

content of the food being cooked. Some foods, such as potatoes have a high moisture content.

Condensation trapped in the door glass should clear after a few hours.

Flashing or arcing from within the

cavity when cooking.

Arcing will occur when a metallic object comes into close proximity to the oven cavity during cooking.

This may possibly roughen the surface of the cavity, but would not otherwise damage the oven.

Arcing potatoes. Ensure all "eyes" are removed from the potatoes and that they have been pierced, place directly onto

the turntable or in a heat resistant  an dish or similar.

The display is lit but the control

panel will not work when pressed.

Check the door is closed properly.

Oven cooks too slowly. Ensure correct power level has been selected.

Oven makes a noise. The microwave energy pulses ON and OFF during cooking/defrosting.

Outer cabinet is hot. The cabinet may become warm to the touch - keep children away.

WARNING: Never adjust, repair or modify the oven yourself. It

is hazardous for anyone other than a SHARP trained engineer

to carry out servicing or repairs.

This is important as it may involve the removal of covers that

provide protection against microwave energy.

• The door seal stops microwave leakage during oven operation, but

does not form an airtight seal. It is normal to see drops of water,

light or feel warm air around the oven door. Food with a high

moisture content will release steam and cause condensation inside

the door which may drip from the oven.

• Repairs and Modi cations: Do not attempt to operate the oven if

it is not working properly.

• Outer Cabinet & Lamp Access: Never remove the outer cabinet.

This is very dangerous due to high voltage parts inside which must

never be touched, as this could be fatal.

Your oven is not  tted with a lamp access cover. If the lamp fails, do

not attempt to replace the lamp yourself, call a SHARP approved

service facility.

If you think the oven is not working properly there are some simple

checks you can carry out yourself before calling an engineer. This

will help prevent unnecessary service calls if the fault is something

simple.

Follow this simple check below:

Place half a cup of water on the turntable and close the door.

Programme the oven to cook for 1 minute using 100% microwave

power.

1. Does the oven lamp come on when it is cooking?

2. Does the turntable rotate?

3. Does the cooling fan work? (Check by placing your hand above

the air vent openings.)

4. After 1 minute does the audible signal sound?

5. Is the water in the cup hot?

If you answer “NO” to any question first check that the oven is

plugged in properly and the fuse has not blown. If there is no

fault with either, check against the troubleshooting chart below.

TO REPLACE THE MAINS PLUG

IMPORTANT

•

The fuse from the cut-o plug should be removed and the plug

disposed of in a safe manner.

•

Under no circumstances should the cut-o plug be inserted into

a socket outlet as a serious electric shock may occur.

•

The plug must not be used without the fuse cover  tted.

If you have any doubt about your microwave oven obtain the help

of a qualified electrician. When replacing the plug please ensure

that you use a BSI or ASTA approved plug to BS1363, this should be

 tted with a brown coloured 13 amp fuse approved by BSI or ASTA

to BSI 362. If you have any doubt about electrical connection seek

the help of a quali ed electrician.

The wires in the mains cable are colour coded as shown:

Green and yellow stripes = EARTH

Blue = NEUTRAL

Brown = LIVE

As the colours in the mains lead of your oven may not correspond

with the coloured marking identifying the terminals in your plug,

connect the wires as described:

•

The green and yellow wire to the plug terminal marked E or

or coloured green or coloured green and yellow.

•

The blue wire to the plug terminal marked N or coloured black or

coloured blue.

•

The brown wire to the plug terminal marked L or coloured red or

coloured brown.

Make sure the terminal screws are tight and the cable is held

securely by the cable grip where it enters the plug.

Like most appliances in your home, your oven must be connected to a

single phase 230-240V~, 50Hz alternating current supply.

If you do not make the proper electrical connections you might

damage the oven or injure yourself. Neither SHARP nor the supplier

will be liable if this happens.

WARNING: THIS APPLIANCE MUST BE EARTHED

If you have any doubts about your electrical supply ask a

quali ed electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp R-622STM Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info