Bedienungsanleitung Sharp UD-P16E-W (Seite 7 von 46) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

787899

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

Memory function

1. If the unit is turned o via the POWER button, when turned back on

again it will resume from the function it was turned o in. Note that if

the timer was set or if the unit was in the lock mode, these settings are

not stored.

2. If the mains power is disconnected while the unit is operating, it will

not start automatically when the mains is reconnected. When the mains

power is applied again, you will need to press the POWER button to

restart operation. The unit will start up in the initial mode.

Water tank full auto-stop function

When the water tank is full, the unit will stop operation, the air outlet

louver will close and a buzzer will sound. To reset, remove the water tank,

empty and replace. When the empty water tank is put back into the unit, it

will restart. Note that the compressor will take about 3 minutes to operate.

Auto defrost

If the unit is used in a low temperature environment, the internal

evaporator may be covered by frost. In order to make sure the machine

operates normally, the machine has auto-defrost function. Should

the internal sensor detect a temperature of ≤-1°C the machine will

enter auto-defrost function. That means it will run continuously in the

dehumidication mode for 30 minutes, then the machine will start the

defrost cycle, the DEFROST light will illuminate, the compressor will stop

and that fan will operate at high speed.

When temperature of evaporator is ≥2°C and the unit has been in the

defrost mode for 10 minutes, the auto-defrost mode will turn o and the

compressor turns on. At this point the unit will start to dehumidify and the

DEFROST light will turn o.

While in the defrost mode and the temperature of the evaporator is ≥0°C

for two minutes, the defrost function is cancelled.

Compressor protection function

Should there be a problem with the unit causing the compressor to stop,

the compressor will turn o for 3 minutes. Normally the compressor will

restart after 3 minutes, if it does not unplug the unit for an hour and try

again. If it still does not start, call for service.

High/Low temperature protection

function

If the unit detects that the ambient temperature is outside of the normal

operating range of 5°C to 38°C, it will shut down. When the normal

operating range is reached, the compressor will start. Note that it will take

the compressor 3 minutes to start working once the normal temperature

range is met.

Low humidity protection function

If the unit detects low humidity of <30% the display will indicate LO and

it will stop any dehumidifying action and the fan will operate a the lowest

speed.

If the humidity is over 80%, the display will indicate HI and keep

dehumidifying.

High temperature fan speed switch

function

When the unit is dehumidifying in a high temperature environment and

the fan speed is set to low, it will switch automatically to the high speed.

This is to prevent excessive load on the compressor. When the ambient air

temperature reduces, the fan speed will return to the low setting.

Error codes

There are number of error codes which may appear in the display, these are

as below. When the error code is displayed, it will ash. If any of these error

codes are experienced, call for service.

C1 – Indicates that there is a fault with the evaporator temperature sensor.

In this condition, the unit will stop working.

C2 – Indicates that there is a fault with the ambient air temperature sensor.

In this condition, the unit will stop working.

C8 – The temperature of the evaporator checked every 8 minutes, if this is

within ≤3°C of the ambient air temperature for 5 consecutive checks, the

unit will shut down and the error code C8 is displayed.

Continuous drainage function

Should it be necessary to provide continuous drainage, this can be

achieved by tting a 15mm inner diameter pipe to the drainage hole on

the rear of the unit. When installed, water will drain through the pipe and

not into the water tank.

Ensure that the drainage pipe runs in a downwards direction, and it not

bent or damaged in any way so that the water runs freely out of the unit.

When tting the drainage pipe, make sure that it is pushed all the way into

the drainage hole so that it pushed over the drain outlet which is located

about 70mm inside the unit from the rear cover of the unit.

Refer to the 3 on page 1 for the location of the drainpipe connection port.

Maintenance

When cleaning your dehumidier:

• Use a soft clean cloth.

• Do not use the alcohol, gasoline, and other benzene chemical solvents.

• To clean the lter, remove it, then use a vacuum cleaner to clear any dust

which may have built up. If necessary, use water to clean, then place it in

ventilated area until dry.

• Unplug the unit from the mains supply before cleaning.

Other advice:

• Before moving the unit, unplug the mains supply and pull out the water

in tank.

• If not using the unit for a long time, unplug the unit from the mains sup-

ply, empty the water tank, wait for 2 days to make sure the unit inside

completely dry before packing.

• Always store the unit in an upright position.

• Do not tilt the unit horizontally or turn upside down.

• If the unit requires repair, seek help of a professional person.

Sharp UD-P16E-W Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info